User manual ONKYO TA-6711

[. . . ] TA-6711 Ster eo Cassette Tape Deck REC LEVEL 5 4 6 EJECT 3 7 TIMER REC OFF PLAY 2 8 1 9 3 HEAD DUAL CAPSTAN DIMMER ELAP/REMA RESET T- SIZE MPX FILTER DOLBY NR AUTO ACCUBIAS TAPE MONITOR 0 10 REW POWER FF REC PAUSE STOP PLAY L MONO MIC R ACCUBIAS REC BALANCE L R ON OFF STEREO CASSETTE TAPE DECK TA- 6711 Instruction Manual CONTENTS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Control Position and Names . . . . . . . . . . . . . . . . [. . . ] · Confirm that the cassette deck is properly connected to the amplifier and other components in the system. RESET Dolby NR REC LEVEL oREC REC BALANCE gPAUSE AUTO ACCUBIAS ACCUBIAS 1 2 Recording Confirm that the amplifier is set up correctly for recording. (Refer to the amplifier's instruction manual for details. ) 1. Make sure the side to be recorded is facing outward. Prepare the source component to be used for the recording. · Tune in the desired station on the tuner. · Load a CD (or LP) into the CD player (or turntable). · Load a cassette into the tape player (analog or DAT). Select the DOLBY B NR, DOLBY C NR or OFF setting. Press the RESET button to return the Real Time Counter to [0:00]. · If desired, the MPX FILTER button may be used when recording FM broadcasts. Press the g PAUSE button while holding the o REC button down. If the g PAUSE button is pressed first, the unit switches to the pause mode instead of the rec/pause mode. Note that when this happens the input selector of an Onkyo amplifier (or receiver) connected to the unit will switch automatically to the TAPE position. · The ACCUBIAS SET indicator will flash to indicate that the Auto Accubias setting has started. During this period, the unit carries out necessary operations to determine the optimal recording bias and level. When these operations are completed the ACCUBIAS SET indicator stays lit. For details, refer to "Using the Auto Accubias System" on page 11. · To clear the Auto Accubias setting, press the AUTO ACCUBIAS button again or eject the tape. · The recording bias can be adjusted manually as desired. See "Manually Adjusting the Recording Bias" on page 11. 3 DOLBY NR B C OFF 4 RESET 6 REC PAUSE 7 AUTO ACCUBIAS ACCUBIAS SET 10 8 REC BALANCE 2 3 REC LEVEL 5 4 6 7 8 L R 1 9 0 10 9 PLAY REAL TIME COUNTER ELAPSED PEAK LEVEL(dB) L CH R CH 30 20 14 10 6 4 2 0 DOLBY NR B +2 +4 OPERATION REC +6 +10 8. While observing the peak level indicators, adjust the recording level and balance as appropriate. · Adjust the REC BALANCE knob so that the level of the left and right channels is approximately the same. [. . . ] (Dolby B or C) for the tape being played back. Remedy: Confirm that cassette has tape type detection holes. Cause: Tape not encoded with Dolby NR played back with Dolby B or C NR on. Remedy: Select the appropriate NR mode using the DOLBY NR button (OFF). [. . . ]