User manual ONKYO TA-RW66 service manual

[. . . ] 4 System Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Playing Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Real Time Counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the ELAP/REMA button to switch the Real Time Counter to the "REMAIN'' (remaining) time mode. The Real Time Counter will display the tape size flashing for a few seconds, then the time remaining on the cassette (based on the tape size setting) will be displayed. · After the remaining time has counted down the 0:00, the indication " " flashes on and off on the display. · Press the counter mode button while the tape size is being displayed to return to 2 3 4 ELAP/REMA T- SIZE REMAIN PLAY REAL TIME COUNTER ELAPSED REMAIN PEAK LEVEL(dB) BIAS L CH START R CH 30 20 14 MPX FILTER 10 6 4 ACCUBIAS SET 2 DOLBY NR OFF 0 B +2 C +4 OPERATION REC +6 +10 the counter display. REAL TIME COUNTER DOLBY NR B 30 20 14 10 6 4 2 0 +2 +4 OPERATION T- SIZE REMAIN PEAK LEVEL(dB) L CH R CH To choose the Tape Size Setting after Playback or Recording has Started +10 +6 REAL TIME COUNTER REMAIN PEAK LEVEL(dB) L CH R CH 30 20 14 10 6 4 2 0 DOLBY NR B +2 +4 OPERATION +6 +10 Press the T-SIZE button once. If you accidentally set the wrong tape length, press the T- SIZE button again to set the correct length (without stopping playback or recording) to obtain the correct remaining time reading. The remaining time is automatically recalculated when the remaining time counter reaches [6:00]. The display changes briefly to the tape's length [e. g. : C-60], then the new (more accurate) remaining time is displayed. To Obtain the Most Accurate Time Indications Possible T- SIZE Press the T-SIZE button when the current side is almost finished playing. The deck will recalculate the remaining time and a more accurate indication will appear. 9 Recording If recording does not begin even when the steps listed below are followed: · Check to see if one or both of the cassette's erasure prevention tabs have been broken off. · Confirm that the cassette deck is properly connected to the amplifier and other components in the system. RESET Dolby NR REC LEVEL oREC REC BALANCE gPAUSE AUTO ACCUBIAS ACCUBIAS 1 2 Recording Confirm that the amplifier is set up correctly for recording. (Refer to the amplifier's instruction manual for details. ) 1. Make sure the side to be recorded is facing outward. Put the source component into recording standby status. · Temporarily stop CD (or LP) play. · Rewind the tape to a position immediately preceding the portion you wish to play. Initiate play on the source component and press the s PLAY button on the tape deck at the same time. You can also use the CD Synchro Recording function if the tape deck is properly connected to an Onkyo CD player bearing the z mark. Using the Auto Accubias System Auto Accubias is a system that allows you to automatically set the optimal recording bias and level for the tape being used. To activate this system, simply press the AUTO ACCUBIAS button when the unit is in the recording-standby mode. While the system is calculating the optimal settings (the ACCUBIAS SET indicator flashes), the tape is automatically fast forwarded and rewound, a test signal is recorded on it and then played back. In the display, the flashing bias indicators move to the right and left, and stop at the 0 position. When the optimal bias and level settings have been set, the ACCUBIAS SET indicator stays lit and the tape is rewound to the position where the setting was started. Note: Do not initiate the Auto Accubias function when the tape is near the end of the side. Manually Adjusting the Recording Bias Although the Auto Accubias system may be used to set the recording bias and level as explained above, you can adjust the recording bias independently for the right and left channels when the unit is in recording-standby mode or simultaneously during recording. [. . . ] Cause: Connecting cables not inserted firmly. Cause: External flux leakage from nearby amplifier or TV set. Cause: Dolby NR encoded tape played back with NR off. Remedy: Select the appropriate NR mode using the DOLBY NR button. [. . . ]