User manual ONKYO TA-RW99 service manual

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] Changing the value from "0" to "5" will spread the sound of the center channel to left and right (outwards). Source Setup Items can be set individually for each input selector. Preparation Press the input selector buttons to select an input source. Main menu Source Setup Audyssey The tone for each speaker is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup. To enable the following settings, you must first perform the Room Correction and Speaker Setup ( page 31). Audyssey Off Movie: Select this setting for movie material. Music: Select this setting for music material. The Audyssey indicator lights. Note · If the "Audyssey" setting is set to "Off", the "Equalizer" settings are applied ( page 48). · When "Audyssey Quick Start" has been used for measurement, the "Audyssey"setting cannot be selected. · Audyssey equalizing does not work with DSD sources. · These technologies cannot be used when: ­ a pair of headphones is connected, or ­ either Pure Audio (European, Australian and Asian models) or Direct listening mode is selected. Audyssey DSXTM Soundstage ­3dB to Reference to +3dB With this setting, you can adjust the sound stage when using Audyssey DSX. Note · This listening mode can be selected only when all the following conditions are satisfied: ­ The center speaker is connected. ­ The front high speakers are connected. Theater-Dimensional Listening Angle Wide: Select if the listening angle is 40 degrees. Narrow: Select if the listening angle is 20 degrees. The result is bass response, tonal balance, and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution. Audyssey Dynamic EQ works well by itself. However, if Audyssey 2EQ is on, the two technologies work in tandem to provide well-balanced sound for every listener at any volume level. About Audyssey Dynamic Volume® Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic Volume works fine by itself, but can also be used with Audyssey Dynamic EQ. When both are on, Audyssey Dynamic EQ adjusts the perceived bass response, tonal balance, surround impression, and dialog clarity whether watching movies, flipping between television channels, or changing from stereo to surround sound content, when Dynamic Volume adjusts the volume. Dynamic Volume Off Light: Activates Light Compression Mode. Medium: Activates Medium Compression Mode. Heavy: Activates Heavy Compression Mode. [. . . ] Connect the HDMI OUT jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note · When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary ( page 57). Confirm the settings. Turn on the power for all connected components. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation. [. . . ]