User manual ONKYO TX-108

[. . . ] 48 Using the Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Enjoying the Listening Modes . . . . . 60 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. [. . . ] In Category Search mode, you can only select channels from the currently selected category. Channel number & preset number 2 TUNING Category Artist Song title Displaying XM Radio Information Listening mode 1 AV receiver DISPLAY On the AV receiver, press the [DISPLAY] button repeatedly to cycle through the available information. Note: If the category, artist, or song title is not available, "- - -" will be displayed instead. Displaying XM Information on Your TV When you select a different XM channel, or the artist or song title changes, the following information is displayed on your TV for 5 seconds. XM [Category name] [Channel name] [Artist name / Song Title] [Ch. No] Remote controller RECEIVER On the remote controller, press the [RECEIVER] REMOTE MODE button, and then press the [DISPLAY] button repeatedly. DISPLAY Tip: You can display this information at anytime by pressing the [DISPLAY] button. 54 Listening to the Radio--Continued 4 ON STANDBY I TV INPUT Adjust the position of the XM antenna so that the "Signal Quality" is at least 70%. 4-3. XM Antenna Aiming -------TUNER------------a. Signal Quality :100% [ | ] V1 V2 V3 1 V4 2 MULTI CH 3 DVD + T V CH 4 CD 5 TAPE 6 TUNER - 7 PHONO 8 0 MACRO 9 T V VOL CLEAR 12 +10 11 - - / - - - 10 INPUT SELECTOR 1 2 3 ZONE2 1 2, 3 REMOTE MODE RECEIVER TAPE/AMP TV VCR CABLE CDR SAT MD DVD CD HDD The signal quality range is 0% to 100%. DIMMER P TO SLEEP MEN U 5 MEN U + CH DISC ALBUM When you've finished, press the [SETUP] button. Setup closes. ENTER VOL PREV CH DISPLAY RE TURN SE T UP 1, 5 MUTING RANDOM Note: If the signal quality is 0%, make sure that the XM antenna is connected properly. REC PLAYLIST LISTENING MODE STEREO SURR Positioning the XM Antenna You can check the signal strength of the XM radio signal and adjust the position of the XM antenna accordingly. XM Radio Messages The following messages may appear while using XM radio. 1 RECEIVER Press the remote controller's [RECEIVER] button, followed by the [SETUP] button. The XM antenna is not connected properly. Check the antenna. 2 ENTER Use the Up and Down [ ]/[ ] buttons to select "4. Input Setup, " and then press [ENTER]. The XM user encryption code is being updated. Please wait. ENTER 3 ENTER The signal is too weak. Check the antenna connection and reposition it for the best reception. Use the Up and Down [ ]/[ ] buttons to select "3. XM Antenna Aiming, " and then press [ENTER]. 4. Input Setup -------TUNER------------1. Delay 2. Character Edit 3. XM Antenna Aiming The AV receiver is tuning or decoding audio or text data. Please wait. ENTER The XM channel you selected is not currently broadcasting. Headphones While a pair of headphones is connected, you can adjust the volume of each headphone speaker, from ­12 dB to +12 dB each. RC-620M MASTER VOLUME STANDBY/ON STANDBY ZONE 2 POWER ON OFF PURE AUDIO MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 PHONO TAPE TUNER CD DISPLAY PHONES ZONE 2 OFF TONE STEREO DIMMER MEMORY TUNING MODE VIDEO 4 INPUT SETUP RETURN ENTER SETUP MIC LISTENING MODE ZONE 2 LEVEL CLEAR PRESET TUNING PRESET DIGITAL S VIDEO VIDEO L AUDIO R · These settings are stored when the AV receiver is set to Standby. PHONES DIMMER DISPLAY Muting the AV Receiver You can temporarily mute the output of the AV receiver. Setting the Display Brightness You can adjust the brightness of the display. MUTING Remote controller DIMMER AV receiver DIMMER Press the remote controller's [DIMMER] button repeatedly to select: · Normal + VOLUME light on. You can also use the AV receiver's [DIMMER] button (not European models). Press the remote controller's [MUTING] button. The output is muted and the MUTING indicator flashes on the display. To unmute the AV receiver, press the remote controller's [MUTING] button again, or adjust the volume. The output is unmuted and the MUTING indicator goes off. Muting is cancelled when the AV receiver is set to Standby. Tip: You can choose how much the output is muted by using the Muting Level preference (see page 78). 58 Common Functions--Continued Using the Sleep Timer With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period. SLEEP Displaying Source Information You can display various information about the current input source as follows. Remote controller Press the remote controller's [SLEEP] button repeatedly to select the required sleep time. You can set the sleep time from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears. SLEEP indicator DISPLAY Press the [DISPLAY] button repeatedly to cycle through the available information. AV receiver DISPLAY The following information can typically be displayed: Input source & volume Signal format* or sampling frequency Input source & listening mode To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack. STANDBY/ON STANDBY ZONE 2 *If the input signal is analog, no format information is displayed. [. . . ] Before you record important data, make sure that the material will be recorded correctly. To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VIDEO 1] button, press the [STANDBY/ON] button. "Clear" will appear on the display and the AV receiver will enter Standby mode. For North American and Australian models, set the AV receiver to Standby before disconnecting the power cord from the wall outlet. [. . . ]