User manual ONKYO TX-8410R

[. . . ] 62 Listening to the Radio . . . . . . . . . . . . . . . . . . 63 Enjoying the Listening Modes . . . . . 71 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. [. . . ] For other models it's 0. 05 MHz steps for FM and 9 kHz steps for AM. In Manual Tuning mode, FM stations will be in mono. Tuning into Weak FM Stereo Stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. TUNER (Actual display depends on country. ) Tuning into AM/FM Radio Stations Auto Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator appears on the display. 2 TUNING TUNING Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator also appears. TUNED AUTO FM STEREO 63 Listening to the Radio--Continued Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. Displaying AM/FM Radio Information DISPLAY MASTER VOLUME STANDBY/ON STANDBY READY ON STANDBY TV INPUT ZONE 2 ZONE 3 Number buttons DVD VCR/DVR CBL/SAT PURE AUDIO AUDIO SEL DVD VCR/DVR CBL/SAT GAME/TV AUX 1 AUX 2 TAPE TUNER CD PHONO DISPLAY 1 GAME/TV 2 AUX1 3 AUX2 + TV CH PUSH TO OPEN 4 TAPE 5 TUNER 6 CD - 7 PHONO 8 0 9 D. TUN TV VOL +10 CLEAR 12 11 --/--- 10 INPUT SELECTOR MACRO D. TUN ZONE3 1 2 3 REMOTE MODE DVD VCR CD CDR/MD TV DIMMER P TO U MEN MEN U ZONE2 Press the [DISPLAY] button to display the available information. RECEIVER DISPLAY CABLE SAT DOCK RECEIVER TAPE/AMP SLEEP 1 RECEIVER Press the [RECEIVER] button, followed by the [D. TUN] button. The [RECEIVER] button flashes. Band Frequency Preset # D. TUN Listening mode CLEAR (Actual display depends on country. ) Note: · When you select a preset with a custom name (see page 94), its name is displayed instead of the band and frequency. 2 DVD VCR/DVR CBL/SAT 1 GAME/TV 2 AUX1 3 AUX2 4 TAPE 5 TUNER 6 CD Within 8 seconds, use the number buttons to enter the frequency of the radio station. For example, to tune to 87. 5 (FM), press 8, 7, 5. Note: While the [RECEIVER] button is flashing, you cannot select another input source with the remote controller. 7 PHONO 8 0 9 +10 64 Listening to the Radio--Continued Using RDS (not North American model) RDS only works in areas where RDS broadcasts are available. TUN RETURN TV VOL SETUP MIC AUX 2 INPUT SETUP PRESET +10 PURE AUDIO AUDIO SEL DVD VCR/DVR CBL/SAT GAME/TV AUX 1 AUX 2 TAPE TUNER CD PHONO DISPLAY ON OFF CLEAR 12 ENTER S VIDEO VIDEO L AUDIO R DIGITAL PUSH TO OPEN ZONE 3 DIGITAL INPUT LISTENING MODE ZONE 2 PHONES POWER OFF LEVEL TONE HDMI OUT STEREO THX RT/PTY/TP MEMORY TUNING MODE SETUP TUNING 11 --/--- 10 INPUT SELECTOR MACRO CLEAR TUNING RETURN SETUP MIC AUX 2 INPUT PRESET CLEAR ZONE 3 DIGITAL INPUT LISTENING MODE TUNING ENTER S VIDEO VIDEO L AUDIO R DIGITAL ON OFF 1 2 3 ZONE3 REMOTE MODE DVD VCR CD CDR/MD TV CABLE SAT DIMMER P TO U MEN MEN U ZONE2 DOCK RECEIVER TAPE/AMP SLEEP You can store a combination of up to 40 of your favorite AM and FM radio stations. + 1 2 MEMORY Tune into the AM or FM station you want to store as a preset. The preset number flashes. CH +/­ CH DISC ALBUM ENTER VOL PREV CH DISPLAY GU IDE EXIT SE TUP RN RETU MUTING PRESET 3 PRESET While the preset number is flashing (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 40. To select a preset, use the PRESET [ ]/[ ] buttons or the remote controller's CH [+/­] button. + CH DISC ALBUM - 4 MEMORY Press the [MEMORY] button again to store the station. The station is stored and the preset number stops flashing. Repeat this procedure for all of your favorite stations. Deleting Presets 2 MASTER VOLUME STANDBY/ON STANDBY Note: · You can name your radio presets for easy identification (see page 94). READY ZONE 2 ZONE 3 PURE AUDIO AUDIO SEL DVD VCR/DVR CBL/SAT GAME/TV AUX 1 AUX 2 TAPE TUNER CD PHONO DISPLAY PUSH TO OPEN ZONE 2 PHONES POWER OFF LEVEL TONE HDMI OUT STEREO THX RT/PTY/TP MEMORY TUNING MODE SETUP TUNING RETURN SETUP MIC AUX 2 INPUT PRESET CLEAR ZONE 3 DIGITAL INPUT LISTENING MODE TUNING ENTER S VIDEO VIDEO L AUDIO R DIGITAL ON OFF 1 2 Select the preset that you want to delete. While holding down the [MEMORY] button, press the [TUNING MODE] button. The preset is deleted and its number disappears from the display. TUNING MEMORY MODE CLEAR 67 Common Functions This section explains functions that can be used with any input source. GAME/TV AUX1 AUX2 TV CH Adjusting Speaker Levels You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV receiver is set to Standby. 4 TAPE 5 TUNER 6 CD - 7 PHONO 8 0 9 D. TUN TV VOL +10 CLEAR 12 11 --/--- 10 INPUT SELECTOR MACRO 1 2 3 ZONE3 REMOTE MODE DVD VCR CD CDR/MD TV DIMMER CABLE SAT DOCK RECEIVER TAPE/AMP SLEEP P TO U MEN MEN U ZONE2 Press [RECEIVER] first SLEEP LEVEL CH SEL DIMMER + CH DISC ALBUM LEVEL ENTER VOL - GU IDE EXIT Use the remote controller's [CH SEL] button to select each speaker, and use the [LEVEL­] and [LEVEL+] buttons to adjust the volume. You can adjust the volume of each speaker from ­12 dB to +12 dB (­15 dB to +12 dB for the subwoofer). DISPLAY PREV CH DISPLAY SE TUP RN RETU MUTING MUTING REC PLAYLIST RANDOM LISTENING MODE STEREO REPEAT PURE A SURR AUDIO DIRECT SUBTITLE PLAY MODE THX ALL ST CH SEL TEST TONE CH SEL LEVEL- LEVEL+ OPEN/CLOSE VIDEO OFF AUDIO SEL VCR L NIGHT DVD Re-EQ HDD LEVEL ­ + Notes: · You cannot use this function while the AV receiver is muted. · Speakers that are set to No or None in the Speaker Configuration cannot be adjusted (see page 86). Headphones While a pair of headphones is connected, you can use the [CH SEL], [LEVEL­], and [LEVEL+] buttons to adjust the volume of each headphone speaker (left and right), from ­12 dB to +12 dB each. RC-690M MASTER VOLUME STANDBY/ON STANDBY ZONE 2 ZONE 3 PURE AUDIO AUDIO SEL DVD VCR/DVR CBL/SAT GAME/TV AUX 1 AUX 2 TAPE TUNER CD PHONO DISPLAY PUSH TO OPEN ZONE 2 PHONES OFF LEVEL TONE HDMI OUT STEREO THX DIMMER MEMORY TUNING MODE SETUP TUNING RETURN SETUP MIC AUX 2 INPUT PRESET CLEAR ZONE 3 DIGITAL INPUT LISTENING MODE TUNING ENTER S VIDEO VIDEO L AUDIO R DIGITAL These settings are stored when the AV receiver is set to Standby. PHONES DIMMER DISPLAY Muting the AV Receiver Setting the Display Brightness You can adjust the brightness of the display. Remote controller DIMMER You can temporarily mute the output of the AV receiver. [. . . ] · To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (e. g. , TAPE IN to TAPE OUT or VCR/DVR IN to VCR/DVR OUT). · When the Pure Audio listening mode is selected, video recording is not possible because no video signals are output. Select another listening mode. Remote Controller The remote controller doesn't work · Make sure that the batteries are installed with the correct polarity (page 14). · Make sure that the remote controller is not too far away from the AV receiver and there's no obstruction between the remote controller and the AV receiver's remote control sensor (page 14). [. . . ]