User manual ONKYO TX-890

[. . . ] 37 Using the Listening Modes . . . . . . . . . . 44 Thank you for purchasing an Onkyo AV receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV receiver. [. . . ] Speaker configuration is complete. 33 Playing Your AV Components Basic AV Receiver Operation ON STANDBY I TV INPUT V1 V2 V3 1 2 MULTI CH 3 DVD + T V CH 1 2 STANDBY/ON 4 CD 5 TAPE 6 TUNER - DISPLAY TUNING / PRESET 4 MASTER VOLUME ENTER 7 +10 8 0 MACRO 9 T V VOL CLEAR 12 11 --/ --- 10 INPUT SELECTOR 1 2 3 1 VIDEO 3 INPUT VIDEO L AUDIO R REMOTE MODE RECEIVER TAPE/AMP TV VCR CABLE CDR SAT MD DVD CD HDD STANDBY DIMMER A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE RETURN SETUP SLEEP TO EN PM U CLEAR PHONES MULTl CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD MEN U + CH DISC ALBUM VCR ENTER VOL PREV CH RE TURN 4 UP SET MULTI CH 1 2 DISPLAY MUTING REC PLAYLIST RANDOM SP A SP B LISTENING MODE STEREO REPEAT SURR AUDIO DIRECT SUBTITLE PLAY MODE ALLST 1 AV receiver DVD VIDEO 1 VIDEO 2 VCR VIDEO 3 TAPE TUNER Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] REMOTE MODE button, and then use the INPUT SELECTOR buttons. V3 V1 V2 1 CD 2 3 DVD 6 CD TAPE TUNER On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1, VIDEO 2, and VIDEO 3 input sources respectively. 7 8 9 2 AV receiver A SPEAKERS B Remote controller SP A SP B To turn the speakers on or off, use the AV receiver's SPEAKERS [A] and [B] buttons, or use the remote controller's [SP A] and [SP B] buttons. The A and B speaker indicators show whether each speaker set is on or off. Indicators Note that while speaker set B is on, speaker set A is reduced to 5. 1-channel playback. To watch a DVD or other video source, on your TV, select the video input that's connected to the AV receiver's MONITOR OUT jack. 3 4 AV receiver MASTER VOLUME Remote controller VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The volume can be set to MIN, 1 through 79, or MAX. Since the AV receiver is designed for home theaters, it has a wide volume range for precise adjustment. 5 Select a listening mode and enjoy!See "Using the Listening Modes" on page 44. 34 Playing Your AV Components--Continued Displaying Source Information ON STANDBY I TV INPUT You can display various information about the current input source as follows. + T V CH V1 V2 V3 1 2 MULTI CH 3 DVD RECEIVER MULTI CH 4 CD 5 TAPE 6 TUNER - 7 +10 8 0 MACRO 9 T V VOL CLEAR 12 11 --/--- 10 INPUT SELECTOR 1 2 3 Press the [RECEIVER] REMOTE MODE button, and then press the [DISPLAY] button repeatedly to cycle through the available information. DISPLAY HDD REMOTE MODE RECEIVER RECEIVER TAPE/AMP TV DVD CD VCR CABLE CDR SAT MD DIMMER P TO SLEEP M ENU MEN U The following information can typically be displayed: Input source & volume Signal format* or sampling frequency Input source & listening mode + CH DISC ALBUM ENTER VOL - DISPLAY PREV CH DISPLAY RE TU R N SE T UP MUTING REC PLAYLIST RANDOM SP A SP B LISTENING MODE STEREO REPEAT SURR AUDIO DIRECT SUBTITLE PLAY MODE ALLST TEST TONE CH SEL LEVEL LEVEL OPEN/CLOSE VIDEO OFF L NIGHT CINE FLTR RC-632M *If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. Channel blocking is available for XM radio receivers by calling 1-800XMRADIO. Subscriptions subject to Customer Agreement available at xmradio. com. Only available in the 48 contiguous United States. A warning against reverse engineering: It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE® voice compression software included in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this or any other software contained in an XM Radio is explicitly prohibited from attempting to copy, decompile, reverse engineer, or disassemble the object code, or in any other way convert the object code into humanreadable form. The software is licensed solely for use within this product. Signing Up for XM Satellite Radio Before you can use XM Satellite Radio, you must first sign up for an account. You'll need a major credit card and your XM Satellite Radio ID, which you can get from the AV receiver, as explained below, or from the Connect-and-Play package and itself. 12 TUNING / PRESET MASTER VOLUME STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE RETURN SETUP CLEAR VIDEO 3 INPUT PHONES MULTl CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD VIDEO L AUDIO R VCR 1 TUNER Press the [TUNER] input selector button repeatedly to select XM. If "CHECK ANTENNA" appears on the display, make sure the XM antenna is connected properly. Use the TUNING Up and Down [ ]/[ ] buttons to select channel 0. Your XM Satellite Radio ID number is displayed. [. . . ] · If you've connected an -capable Onkyo MD recorder, CD recorder, or next generation HDD-compatible component to the TAPE IN/OUT jacks, or a DS-A1 Remote Interactive Dock to the VIDEO 2 IN jacks, for the remote controller to work properly, you must set the display to MD, CDR, or HDD (see page 31). · The wrong remote control code has been entered. · The entered remote control code may not be correct. If more than one code is listed, try each one. [. . . ]