User manual ONKYO TX-906

[. . . ] 31 Advanced Operation . . . . . . . . . . . . . . . 42 Advanced Setup . . . . . . . . . . . . . . . . . . . . . . 46 Controlling Other Components . . . . . . . . . . . . . . . . . . . . . . . . . 53 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . [. . . ] The A and B speaker indicators show whether each speaker set is on or off. Note: When you turn on speaker set B, the listening mode for speaker set A is set to Stereo automatically. When you select DVD or another video component, on your TV you'll need to select the video input to which the TX-906 is connected. On some DVD players, you may need to turn the digital audio output on. To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The volume can be set to MIN, 1 through 79, or MAX. The TX-906 is designed for home theater enjoyment. It has a wide volume range, allowing precise adjustment. 3 4 TX-906 Remote controller or VOL 5 Enjoy listening modes. See page 37. 31 Basic Operation--Continued This chapter explains functions that can be used with any input source. Muting the TX-906 You can temporarily mute the output of the TX-906. AMP ON STANDBY I TUNER TV INPUT 1 4 7 +10 --/--TONE 2 5 8 0 3 6 9 + TV CH - T V VOL CLEAR Press the REMOTE MODE [AMP] button, and then press the [MUTING] button. The output is muted and the MUTING indicator flashes on the display, as shown. MUTING REMOTE MODE MUTING _ + V2 AMP TUNER DVD V1 INPUT SELECTOR TV AUX TUN TV DVD AMP DIMMER DIMMER TV INPUT TO SLEEP EN PM U MEN U SLEEP VOL + CH DISC ENTER EXIT PREV CH RE GUIDE SE T T U RN UP DISPLAY MUTING MUTING To unmute the TX-906, press the [MUTING] button again, or adjust the volume. The Mute function is cancelled when the TX-906 is set to Standby. Press and hold these buttons to change the frequency continually. Press once to change the frequency one step at a time. Check your local radio guide for the frequencies of the stations available in your area. 3 + CH DISC 3 TUN - While the MEMORY indicator is displayed, use the CH [+/­] button to select a preset from 1 through 30. In this example, preset #3 is selected. - TUN + 4 P MEM Notes: · The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. · In Manual Tuning mode, FM stations will be in mono. Switch back to Auto Tuning mode for stereo. Tuning into weak FM stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Press the [P MEM] button again to store the station. The station is stored and the preset number stops flashing. Repeat this procedure for all of your favorite radio stations. Selecting Preset Stations 1 AMP TUNER Press the REMOTE MODE [AMP] button, then press the [TUN] INPUT SELECTOR button repeatedly to select either AM or FM. TUN 2 + CH DISC Use the CH [+/­] button to select the presets. - 35 Basic Operation--Continued Displaying Radio Information ON STANDBY I TV INPUT 1 4 7 +10 --/--TONE 2 5 8 0 3 6 9 + TV CH 1 AMP - TUNER T V VOL CLEAR REMOTE MODE Press the REMOTE MODE [AMP] button, then press the [DISPLAY] button on the remote controller repeatedly to cycle through the available information. _ + V2 AMP TUNER DVD V1 INPUT SELECTOR TV AUX TUN TV DVD AMP DISPLAY DIMMER TV INPUT P TO SLEEP MEN U MEN U + CH DISC ENTER When the input source is AM or FM: VOL EXIT GUIDE SE T DISPLAY PREV CH RE T U RN UP DISPLAY MUTING Band, preset # & frequency MHz PLAY MODE SP A SP B RANDOM listening mode AUDIO DIRECT SUBTITLE STEREO ANGLE SURR LAST M DSP REPEAT TUN A-B TUN SEARCH TUN M MEMORY P MEM P MEM - + LEVEL TEST TONE CH SEL LEVEL L. NIGHT + CINE FLTR OPEN/CLOSE VIDEO OFF RC-577S Deleting Presets 1 2 P MEM Select the preset that you want to delete (see the previous section). "Erase" flashes on the display. 3 P MEM While it's flashing, press the [P MEM] button again. [. . . ] · If the TX-906 is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed. · Make sure you've selected the correct remote controller mode (page 10). · When using the remote controller to control other manufacturers' AV components, some buttons may not work as expected. · Make sure you've entered the correct remote control code. 58 Troubleshooting--Continued Can't control other components? [. . . ]