User manual ONKYO TX-DS676

[. . . ] Contents Before using A / V Receiver Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] in the multichannel input mode, check again that the source is connected properly (see page 9). If you wish to assign a video source to the multichannel input source, perform the following setting. If you do not wish to do so, proceed to step 3. Press the SP/SYS SETUP button repeatedly until "Video Assign?" appears and then press the SMART SCAN CONTROLLER. Rotate the SMART SCAN CONTROLLER to select the video source you wish to assign and then press the SMART SCAN CONTROLLER. Start playing the component connected to the MULTI CHANNEL INPUT connectors. Press the CH SEL button on the remote controller to select the speaker. Then, press the LEVEL (+ or -) button to adjust the output level. At the listening position, adjust the speaker output level so that you can hear the same sound volume from all speakers. For the right front, left front, center, right surround and left surround speakers, the output levels can be adjusted within the range between -12dB ~ +12 dB. The adjustment range of the subwoofer, however, is -30 to +10 dB. Rotate the SMART SCAN CONTROLLER to select the output level. Repeat the above steps until you set the output levels for all speakers. 3 3 3 6 ** Multi Ch Input ** Level Setup Left Center Right Left Sur Left Sur Subwoofer = 0dB = +5dB = 0dB = 0dB = 0dB =+10dB · Using the on-screen display 1. Select "Input Selector" and press the right edge of the ENTER/Cursor button. Press the right or left edge of the ENTER/Cursor button to select "MULTI CH. " Then, press the center of the ENTER/ Cursor button. The "Multi Ch Input" screen appears. If you wish to skip assigning a video source, proceed to step 5. To assign a video source, select "Video Assign Setup" and then press the right edge of the ENTER/Cursor button. When "Video Assign Setup" screen appears, move the cursor (which is already located at "MULTI CH") rightward or leftward to select the video source you wish to assign. When selected, press the center of the ENTER/Cursor button to return to the previous screen. Select "Level Setup" and press the right edge of the ENTER/ Cursor button. "Multi Ch Input Level Setup" screen appears. [. . . ] Two "AA" batteries (1. 5 V × 2) Specifications and features are subject to change without notice. Power supply and voltage vary depending on the area in which the unit is purchased. Specifications and features are subject to change without notice. Power supply and voltage vary depending on the area in which the unit is purchased. 61 Control positions and names The illustration shows the front panel of the TX-DS777 model VS. The appearance of the front panel varies depending on the model you purchased. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 DIMMER FM MUTE/ MODE DOWN TUNING UP CHARACTER/ MEMORY SP/SYS SETUP AUDIO ADJUSTMENT BASS/ TREBLE MASTER VOLUME STANDBY/ON DO W N MODE UP PRESET/MODE ADJ STAND BY SMART SCAN CONTROLLER POWER PUSH TO ENTER ON OFF LISTENING MODE DIGITAL/ ANALOG A SPEAKERS B DISPLAY DIRECT STEREO /DTS THX DSP REC OUT CH LEVEL SURROUND MODE PHONES MUL CH INPUT TI VIDEO 4 / VIDEO CAM INPUT DVD VIDEO-1 VIDEO-2 VIDEO-3 VIDEO-4 TAPE FM AM PHONO CD S VIDEO VIDEO L AUDIO R(MONO) AV RECEIVER TX-DS777 24 23 22 21 20 19 18 a b cd e f g h i j SPEAKERS A B REC OUT SLEEP DOLBY DIGITAL PCM DIGITAL DTS MPEG DSP STEREO DIRECT RDS MEMORY TUNED FM STEREO AUTO DOLBY PRO LOGIC ft ch dB k Front panel For more information about buttons or knobs, refer to the pages listed in the brackets ( [ ] ) below. [. . . ]