User manual ONKYO TX-NR1000

[. . . ] Contents AV Receiver Getting Started 2 TX-NR1000 TX-NR5000E Instruction Manual Installation and Connections 18 Operations 48 Setup Menu 82 Using the Remote Controller Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. 124 Miscellaneous 143 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Set the sound from the subwoofer to any of the following: LFE only: The subwoofer outputs only LFE (Low Frequency Effect) information. Bass: The subwoofer outputs not only LFE (Low Frequency Effect) factors but also bass sounds from the front speakers. Speaker Impedance Sub-menu Use this sub-menu to set the impedance level of the TX-NR1000/TX-NR5000E to match the specifications of the speakers you are using. The settings in the Speaker Impedance sub-menu can be configured for Main B and Zone 2 as well as for Main A. The selectable parameters are common to all items. Note: Before you change this setting, be sure to first lower the volume at the TX-NR1000/TX-NR5000E to the minimum level. 8 ohms (default): Select this when the impedance of the connected speaker is 8 ohms or more. 6 ohms: Select this when the impedance of the connected speaker is no lower than 6 ohms and no higher than 8 ohms. 4 ohms: Select this when the impedance of the connected speaker is no lower than 4 ohms and no higher than 6 ohms. · When "BTL for Front" is selected for "Surr Back" from the Speaker Configuration sub-menu, the corresponding "Front L/R" is automatically fixed to "8 ohms, " and the impedance settings for the surround back speakers are also removed. Please verify that the impedance of a connected speaker is 8 ohms or more. · For any speaker that is not available or set to "Not Used" in the Speaker Configuration sub-menu, no associated setting item is displayed. Speaker Distance Sub-menu Measure the distance between the listening position and each speaker. Specifying the distance will synchronize the speakers in terms of the time that sounds from each speaker reach the listening position. This is an important specification for you to enjoy realistic home theater. The settings in the Speaker Distance sub-menu can be configured for both "Main A" and "Main B. " 89 Speaker/Output Setup--Continued Perform the setup procedure below following the operating instructions described on page 86. Select the unit of distance from "Unit. " You can select either "feet" or "meters. " The default varies depending on the region. Enter all the values for every speaker you connected. · For any speaker that is not available or set to "Not Used" in the Speaker Configuration sub-menu, no associated setting item is displayed. · If "Surr Back" is set to "BTL for Front" or "Bi-Amp for Front" on the Speaker Configuration sub-menu, no item for surround back speakers is displayed. When "feet" is selected: Front L, Center, Front R, and Subwoofer can be set at 0. 1 foot intervals in a range from 1. 0 foot to 30. 0 feet. Surr R, Surr Back (or Surr Bk R and Surr Bk L), and Surr L can be set at 0. 1 foot intervals in a range from 1. 0 foot to 30. 0 feet. When "meters" is selected: Front L, Center, Front R, and Subwoofer can be set at 0. 03 meter intervals in a range from 0. 30 meters to 9. 00 meters. Surr R, Surr Back (or Surr Bk R and Surr Bk L), and Surr L can be set at 0. 03 meter intervals in a range from 0. 30 meters to 9. 00 meters. [. . . ] "Not available with Dolby Headphone Off" · Doesn't work with the Dolby Headphone function off. "Not available with Dolby Headphone On" · Doesn't work with the Dolby Headphone function on. "Not available with zone2 out in Line out" · Operation not possible with "1-8. f. Zone 2 Out" set to "Line Out. " "Not available with zone3 out in Line out" · Operation not possible with "1-8. g. [. . . ]