User manual ONKYO TX-NR474

[. . . ] 0 The power cord must be connected only after all other cable connections are completed. 0 We will not accept responsibility for damage arising from the connection of equipment manufactured by other companies. 0 Connect speakers with 4 ≠ to 16 ≠ impedance. Furthermore, available services may vary depending on your area of residence. [. . . ] 0 dB") After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors / , adjust the volume of that frequency between "-6. 0 dB") After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors / , adjust the volume of that frequency between "-6. 0 dB") After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors / , adjust the volume of that frequency between "-6. Multiplex/Mono Multiplex Input Channel Set the audio channel or language to be output when playing multiplex audio or multilingual TV broadcasts etc. "Main (default value)": Main channel only "Sub": Sub channel only "Main / Sub": Main and sub channels will be output at the same time. 0 If multiplex audio is being played, "1+1" will be displayed when on the remote controller is pressed. Set the input channel to use for playing any 2 channel digital source such as Dolby Digital, or analog/PCM source in the Mono listening mode. "Left": Left channel only "Right": Right channel only "Left + Right (default value)" : Left and right channels Center Mono Input Channel Height ∫ 2. Dolby Loudness Management When playing Dolby TrueHD, enable the dialog normalization function which keeps the volume of dialog at a certain level. Note that when this setting is Off while playing Dolby Digital Plus/ Dolby TrueHD, the Late Night function that allows you to enjoy surround at low volumes is fixed to Off. "On (default value)": When this function is to be used "Off": When this function is not to be used Surround En 57 > Before Start > Part Names > Install > Initial Setup > Playback Advanced Setup | Supplementary Information | Others ∫ 3. DTS DTS Auto Surround When inputting DTS signals that include extended channel information, the optimum listening mode is automatically selected according to the extended information contained in the input signal and the speaker configuration of this unit when playing in the straight decoding listening mode. "On (default value)": When this function is to be used "Off": Audio is played using the same amount of channels in the input signal according to the speaker configuration of this unit. IntelliVolume Adjust the volume level difference between the devices connected to the unit. Set a negative (j) value if the volume of the target device is larger than the others and a positive (i) value if smaller. To check the audio, start playback of the connected device. (Default Value is "0dB") ∫ 4. LFE Level Set the low-frequency effect (LFE) level for Dolby Digital series, DTS series, Multichannel PCM, and DSD signals. LFE Level Select the low-frequency effect (LFE) level of each type of signal from "0dB (default value)" to "-¶dB". If the low-frequency effect sound is too strong, select "-20dB" or "-¶dB". Name Edit Set an easy name to each input. The set name will be shown on the main unit display. [. . . ] Video och ljud är inte synkroniserade 0 Video kan fördröjas i förhållande till ljudet beroende på inställningarna och anslutningarna till din tv. 0 Försök med att sätta i/dra ur strömförsörjningen till den 76 > Innan du börjar > Delarnas namn > Installera > Grundinställning > Uppspelning Avancerade inställningar | Ytterligare information | Övrigt ändrats till manuell. Proceduren har bekräftats på följande anordningar: (Gäller i april 2017) Tv:ar av märket Toshiba; tv:ar av märket Sharp; RIHDkompatibla spelare av märkena Onkyo och Integra; spelare och brännare av märket Toshiba; spelare och brännare av märket Sharp (när den används med en tv av märket Sharp) ARC (Audio Return Channel): Genom att ansluta en tv som stöder ARC med en enda HDMI-kabel, kan du inte bara mata ut ljudet och videon från den här apparaten till tv:n, utan du kan också mata in ljudet från tv:n till den här apparaten. 0 Upp till 20 000 spår per mapp kan visas, och mapparna kan ligga i upp till 16 nivåers djup. [. . . ]