User manual ONKYO TX-NR509

[. . . ] Contents AV Receiver Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 TX-NR509 Instruction Manual Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Turning On & Basic Operations . . . . . . 19 Advanced Operations . . . . . . . . . . . . . . . . . 39 Controlling Other Components . . . . 53 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. [. . . ] (If you're not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound. Dolby EX Auto: If the source signal contains a Dolby EX flag, the Dolby EX listening mode is used. Manual: You can select any available listening mode. This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD only. Note · If the "Surround Back" Setting is set to "None" ( page 41), this setting cannot be selected. Dolby PLIIx Music (2ch Input) These settings only apply to 2-channel stereo sources. If you're not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx. Panorama On Off Turn this setting on to broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode. Dimension ­3 to 0 to +3 With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. Higher settings move the sound field backward. If the stereo image feels too wide, or there's too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it's in mono, or there's not enough surround sound, move it backward. DTS Neo:6 Music Center Image 0 to 2 to 5 The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. Changing the value from "0" to "5" will spread the sound of the center channel to left and right (outwards). En 43 Theater-Dimensional Listening Angle Wide: Select if the listening angle is 40 degrees. Narrow: Select if the listening angle is 20 degrees. With this setting, you can optimize the TheaterDimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings. Front left speaker Front right speaker 20°/40° Dynamic EQ Off On: Audyssey Dynamic EQ® becomes active. The Dynamic EQ indicator will light ( page 8). With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels. Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. It does so by selecting the correct frequency response and surround volume levels moment-by-moment so that the content sounds the way it was created at any volume level -- not just at reference level. Note · These technologies cannot be used when: ­ a pair of headphones is connected, or ­ either Pure Audio (European, Australian and Asian) or Direct listening mode is selected. Source Setup Menu Source Setup Preparation Press the input selector buttons to select an input source. Audyssey The tone for each speaker is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup. [. . . ] Turn on the power for all connected components. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation. Turn on the power of the Blu-ray Disc/DVD player/recorder. Start playback on the Blu-ray Disc/DVD player/recorder, and verify the following: · The AV receiver automatically turns on, and selects the input to which the Blu-ray Disc/DVD player/recorder is connected. [. . . ]