User manual ONKYO TX-NR905

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver TX-NR905 Instruction Manual Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Turning On & First Time Setup. . . . . 50 Basic Operation Playing your AV components . . . . . . . [. . . ] (The Powered Zone 2 speakers are not turned off. ) · When you connect a pair of headphones, the listening mode is set to Stereo, unless it was already set to Pure Audio, Mono, Stereo, or Direct, in which case it stays the same. 77 Common Functions--Continued Selecting Audio Inputs Specifying the Digital Signal Format 1 REC PLAYLIST 2 MASTER VOLUME RANDOM SP A SP B LISTENING MODE STANDBY/ON STEREO REPEAT PURE A SURR AUDIO DIRECT SUBTITLE PLAY MODE THX ALL ST STANDBY READY ZONE 2 ZONE 3 TEST TONE CH SEL LEVEL- LEVEL+ PURE AUDIO AUDIO SEL DVD VCR/DVR CBL/SAT GAME/TV AUX 1 AUX 2 TAPE TUNER CD PHONO NET/USB DISPLAY PUSH TO OPEN OPEN/CLOSE VIDEO OFF AUDIO SEL AUDIO SEL VCR L NIGHT DVD Re-EQ HDD ZONE 2 PHONES POWER OFF LEVEL TONE HDMI OUT STEREO THX RT/PTY/TP MEMORY TUNING MODE SETUP TUNING RETURN SETUP MIC AUX 2 INPUT USB PRESET ON OFF CLEAR ZONE 3 DIGITAL INPUT LISTENING MODE TUNING ENTER S VIDEO VIDEO L AUDIO R DIGITAL RC-687M If you connect a component to more than one audio input, such as a DVD player connected to analog, digital, multichannel, and HDMI inputs, you can use the [AUDIO SEL] button to select which audio input you want to use to listen to that component. Press the [AUDIO SEL] button repeatedly to select an audio input: HDMI > Auto > Multich > Analog. HDMI: Selects the assigned HDMI IN, and the HDMI indicator appears on the display. (The HDMI IN must already be assigned to the current input selector. See page 54. ) Auto: Selects the assigned COAXIAL or OPTICAL DIGITAL IN, and the DIGITAL indicator appears on the display. (The DIGITAL IN must already be assigned to the current input selector. See page 58. ) If there is no digital signal, the analog input is used instead. Multich:Selects the multichannel input, and the ANALOG indicator appears on the display. (The multichannel input must already be assigned to the current input selector. See page 60. ) Analog: Selects the analog input, and the ANALOG indicator appears on the display. AUDIO SEL Normally, the AV receiver detects the format of digital input signals automatically. However, if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually. · If the beginnings of tracks from a PCM source are cut off, try the PCM setting. · If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting. 1 AUDIO SEL Press the [AUDIO SEL] button repeatedly to select Auto. 2 While "Auto" is shown on the display, use the Left and Right [ ]/[ ] buttons to select: PCM: Only input signals in PCM format are output, and the PCM indicator lights up. The indicator flashes if the input signal is not PCM. DTS: Only input signals in DTS format are output, and the DTS indicator lights up. The indicator flashes if the input signal is not DTS. Auto (default): The format is detected automatically. If no digital input signal is present, the analog input is used instead. 78 Using the Listening Modes Selecting the Listening Modes For a description of each listening mode, see "About the Listening Modes" on page 84. · The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI). · The listening modes you can select depends on the format of the input signal. To check the format, see "Displaying Source Information" on page 77. · While a pair of headphones is connected, you can only select the Pure Audio, Mono, Direct, or Stereo listening mode. SURR STEREO PURE A DIRECT STEREO REPEAT PURE A Selecting with the Remote Controller TO PM ENU ME N U + CH DISC ALBUM ENTER VOL PREV CH DISPLAY GU IDE EXIT SE TUP RN RETU MUTING REC PLAYLIST RANDOM SP A SP B LISTENING MODE SURR AUDIO DIRECT SUBTITLE PLAY MODE THX ALL ST , ALL ST THX TEST TONE CH SEL LEVEL- LEVEL+ OPEN/CLOSE VIDEO OFF AUDIO SEL VCR L NIGHT DVD Re-EQ HDD RC-687M Selecting on the AV Receiver STEREO THX MASTER VOLUME [STEREO] button This button selects the Stereo listening mode. [SURR] button This button selects the Dolby Digital and DTS listening modes. [. . . ] Playback stops while listening to music files on the server · Make sure your server is compatible with the AV receiver (page 111). · If you download or copy large files on your computer, playback may be interrupted. Try closing any unused programs, use a more powerful computer, or use a dedicated server. · If the server is serving large music files to several networked devices simultaneously, the network may become overloaded and playback may be interrupted. [. . . ]