User manual ONKYO TX-SE500

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Read Instructions ­ All the safety and operating instructions should be read before the appliance is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] Serious classics (CLASSICS): Performances of major orchestral works, symphonies, chamber music, etc. Other music (OTHER M): Music styles not covered by the above categories (e. g. , Jazz, Rhythm & Blues, Folk, Country, and Reggae). · Alarm (ALARM): When an RDS station is making an emergency broadcast, ALARM will flash on the display. 39 Listening to RDS broadcasts (European models only) PRESET RT/PTY/TP / AUDIO ADJUST MASTER VOLUME SETUP RETURN STANDBY/ON TUNING PRESET POWER STANDBY ON OFF LISTENING MODE SURROUND THX REC OUT ZONE 2 OFF LEVEL DISPLAY RT/PTY/TP STEREO DSP MEMORY FM MODE ENTER CLEAR PHONES DIRECT/ PURE AUDIO PURE AUDIO AUDIO SELECTOR DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 TAPE TUNER CD PHONO VIDEO 4 INPUT VCR 1 VCR 2 DIGITAL S VIDEO VIDEO L AUDIO R ENTER TUNER 4. Press the ENTER button. Displaying Radio Text (RT) If the station you are currently tuned into is broadcasting RT signals, they will be displayed in the front display of the TXSR701E/601E. If the station does not, this function will be ignored. To display the radio text, press the RT/PTY/TP button once. · If the station you are currently listening to is not an RDS station, only the frequency of the station will appear. · If "Waiting" appears on the display, more time is required to receive the RT information. When the information is received, the characters will scroll across the front display. · If "No Text Data" appears on the display, RT information is not available. · The display shows the frequency for 3 seconds and returns to program service name. The TX-SE500E/601E will scan until it reaches a station of the program type you selected. If headphones are connected, this also adjusts the volume heard from the headphone speakers. To adjust the volume, either press the VOL buttons on the remote controller or turn the MASTER VOLUME dial. To increase the volume, turn the dial clockwise; to decrease the volume, turn the dial counterclockwise. The volume can be set to Min, 1 to 99, and Max. 41 Selecting an Audio Component RCVR MODE AUDIO ADJUST MASTER VOLUME SETUP RETURN STANDBY/ON TUNING PRESET POWER STANDBY ON OFF LISTENING MODE SURROUND THX CH SEL AUDIO SEL ENTER REC OUT ZONE 2 OFF LEVEL DISPLAY RT/PTY/TP STEREO DSP MEMORY FM MODE CLEAR LEVEL / PHONO VIDEO 4 INPUT DIGITAL S VIDEO VIDEO L AUDIO R PHONES DIRECT/ PURE AUDIO PURE AUDIO AUDIO SELECTOR DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 TAPE TUNER CD VCR 1 VCR 2 TAP TAPE AUDIO SELECTOR Selecting the type of audio input signal Press the AUDIO SELECTOR button on the front panel (or AUDIO SEL button on the remote controller) to change the audio mode. Each time the button is pressed, the mode changes from "Auto" "Multich" (only if DVD is selected as the input source) "Analog" and back to "Auto. " TX-SE500/701E/601/601E AUDIO SELECTOR Notes on DTS: · If you play a DTS-formatted CD or LD when the "PCM" setting is selected on the TX-SE500/701E/601/601E, the DTS encoded signal will not be decoded and noise will be output. This noise could damage the amplifier and speakers. Therefore, be sure to select "Auto" or "DTS" and use the digital input jacks (OPT or COAX) to connect the DTS source. · If you play a DTS-formatted CD or LD when "Auto" is selected, you may hear a noise for a short while until the DTS decoder recognizes the DTS-encoded signal and starts operating. · If you press the pause or skip button on the player while playing a DTS source, a short noise may be heard. In such cases, try playing the source in the "DTS" selected. · The DTS indicator on the TX-SE500/701E/601/601E lights while a DTS source is played. [. . . ] · When "Auto" is set for the digital format setting, time is required to change formats when different sources are played. © Switch from the Auto mode to the current source signal (see page 42). 76 Troubleshooting guide If one of the messages shown below appears "Not available with headphones use" Operation not allowed because headphones are plugged into the TX-SE500/701E/601/601E. "Not available with Multichannel use" Operation not allowed while the multi-channel output is being used. "Not available in this Sp Config" Will not work with the current speaker configuration settings. [. . . ]