User manual ONKYO TX-SR303E

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver TX-SR303 TX-SR303E Instruction Manual Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Turning On & First Time Setup. . . . . 30 Basic Operation Playing your AV components . . . . . . . [. . . ] The volume can be set to MIN, 1 through 79, or MAX. The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment. 5 Select a suitable listening mode and enjoy!See page 42. 34 Playing Your AV Components--Continued Displaying Source Information ON STANDBY REMOTE MODE RECEIVER TAPE/AMP DVD RECEIVER INPUT SELECTOR You can display various information about the current input source as follows. Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information. 1 V1 2 V2 3 V3 CD MULTI CH 4 7 TAPE 5 MULTI CH 6 DVD MD 8 TUNER 9 CD CDR +10 --/--- 0 DIMMER CLR SLEEP DISC CH VOL LISTENING MODE STEREO SURROUND The following information can typically be displayed for input sources. LEVEL+ AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE LEVEL- Input source & volume Signal format* or sampling frequency Input source & listening mode DISPLAY DISPLAY L NIGHT CINE FLTR RC-605S Using the Multichannel Input The multichannel input is for connecting a component with individual 5. 1-channel analog audio output jacks, such as a DVD player or MPEG decoder. Press the [RECEIVER] button followed by the [MULTI CH] button so that MULTI CH indicator appears on the display. Audio from the multichannel input will now be used for the DVD input source. MULTI CH indicator *If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears. Interpreting Surround Channel Information A BC A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). If there's surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes). Note: · While the multichannel input is selected, the Speaker Configuration settings on page 32 are ignored, and signals from the multichannel input are fed to the front left, front right, center, surround left, and surround right speakers and subwoofer regardless of those settings. 35 Using the Tuner Listening to the Radio TUNING MODE TUNING TUNING / PRESET Manual Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. MASTER VOLUME STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 2 TUNING / PRESET ENTER CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD TUNER Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. With the built-in tuner, you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. 1 TUNER Use the [TUNER] input selector button to select either AM or FM. In this example, FM has been selected. The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For European models it's 0. 05 MHz steps for FM and 9 kHz steps for AM. In Manual Tuning mode, FM stations will be in mono. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Band Frequency (Actual display depends on country. ) Tuning into Radio Stations Auto Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator appears on the display. 2 TUNING / PRESET ENTER Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. When tuned into a station, the TUNED indicator appears. [. . . ] · Make sure that the remote controller is not too far away from the AV receiver, and that there's no obstruction between the remote controller and the AV receiver's remote control sensor (page 9). · Make sure you've selected the correct remote controller mode (page 10). · Make sure you've entered the correct remote control code. · Make sure you've selected the correct remote controller mode (page 10). [. . . ]