User manual ONKYO TX-SR307

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 TX-SR307 Turning On & First Time Setup . . . . . 32 Instruction Manual Basic Operations. . . . . . . . . . . . . . . . . . . . . . . . . 38 Using the Listening Modes . . . . . . . . 49 Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Controlling Other Components . . . . 62 Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The volume can be set to Min, 1 through 79, or Max. 5 38 Select a listening mode and enjoy!See "Using the Listening Modes" on page 49. Basic Operations--Continued This section explains functions that can be used with any input source. DISPLAY Press [RECEIVER] first Muting the AV receiver You can temporarily mute the output of the AV receiver. Press the [RECEIVER] button, and then press the remote controller's [MUTING] button. The output is muted and the MUTING indicator flashes on the display. MUTING TONE, +, ­ To unmute the AV receiver, press the remote controller's [MUTING] button again, or adjust the volume. The output is unmuted and the MUTING indicator goes off. Muting is cancelled when the AV receiver is set to Standby. DIMMER SLEEP Using the Sleep Timer With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period. Press the [RECEIVER] button, and then press the remote controller's [SLEEP] button repeatedly to select the required sleep time. You can set the sleep time from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears. SLEEP indicator MUSIC OPTIMIZER ­, +, TONE DISPLAY PHONES DIMMER Setting the Display Brightness You can adjust the brightness of the display. Remote controller Press the [RECEIVER] button, and then press the remote controller's [DIMMER] button repeatedly to select: dim, dimmer, or normal brightness. You can also use the AV receiver's [DIMMER] button (not European models). To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. AV receiver 39 Basic Operations--Continued 7Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack. Displaying Source Information You can display various information about the current input source as follows. Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information. Notes: · Always turn down the volume before connecting your headphones. · While the headphones plug is inserted in the PHONES jack, the speakers are turned off. · Speaker sets A and B are turned off while the headphones plug is inserted in the PHONES jack. · When you connect a pair of headphones, the listening mode is set to Stereo, unless it's already set to Mono, Stereo, or Direct, in which case it stays the same. Note: This procedure can also be performed on the AV receiver by using its [DISPLAY] button. The following information can typically be displayed: Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode *1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. Adjusting the Bass & Treble You can adjust the bass or treble for speaker set A's front speakers, except when the Direct listening mode is selected. AV receiver Press the [TONE] button repeatedly to select either "Bass" or "Treble". [. . . ] How do I change the language of a multiplex source · On the "7. Audio Adjust" menu, change the "Input (Mux)" setting to "Main" or "Sub" (page 57). The functions don't work · To use , you must make an connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 31). When performing "Audyssey 2EQTM Room Correction and Speaker Setup", the measurement fails showing the message "Ambient noise is too high". [. . . ]