User manual ONKYO TX-SR503

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver TX-SR503 TX-SR503E TX-SR8350 Instruction Manual Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Turning On & First Time Setup. . . . . 30 Basic Operation Playing your AV components . . . . . . . [. . . ] If there's surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes). Note: · While the multichannel input is selected, the Speaker Configuration settings on page 32 are ignored, and signals from the multichannel input are fed to the front left, front right, center, surround left, and surround right speakers and subwoofer regardless of those settings. 35 Using the Tuner Listening to the Radio TUNING MODE TUNING TUNING / PRESET Tuning into Radio Stations Auto Tuning Mode 1 TUNING MODE MASTER VOLUME STANDBY/ON ENTER Press the [TUNING MODE] button so that the AUTO indicator appears on the display. STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR VIDEO 3 INPUT PHONES PURE AUDIO MULTl CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD VIDEO L AUDIO R VCR 2 TUNING / PRESET TUNER ENTER Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. With the built-in tuner, you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. 1 TUNER Use the [TUNER] input selector button to select either AM or FM. In this example, FM has been selected. When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator appears on the display, as shown. TUNED AUTO Band Frequency FM STEREO (Actual display depends on country. ) Manual Tuning Mode AM Frequency Step Setup (not North America and Europe) Here you can specify the AM frequency step used in your area. When this setting is changed, all radio presets are deleted. 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. 1 Press the [SETUP] button and use the Up and Down [ ]/[ ] buttons to select "0. Hardware Setup, " and then press [ENTER]. Use the Up and Down [ ]/[ ] buttons to select "AM Freq, " and then use the Left and Right [ ]/[ ] buttons to select: 10 kHz: Select if 10 kHz steps are used in your area. 9 kHz: Select if 9 kHz steps are used in your area. Setup closes. 2 TUNING / PRESET ENTER 2 Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz steps for AM. In Manual Tuning mode, FM stations will be in mono. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. 3 Note: · This procedure can also be performed on the remote controller by using its [SETUP] button, arrow buttons, and [ENTER] button. 36 Using the Tuner--Continued Presetting Radio Stations Deleting Presets 2, 4 STANDBY/ON 3 TUNING / PRESET 2 MASTER VOLUME TUNING / PRESET MASTER VOLUME STANDBY/ON ENTER ENTER STANDBY STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR CLEAR VIDEO 3 INPUT PHONES PURE AUDIO MULTl CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD VIDEO 3 INPUT R PHONES PURE AUDIO MULTl CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD VIDEO L AUDIO VIDEO L AUDIO R VCR VCR You can store up to 30 of your favorite radio stations as presets. 1 2 MEMORY TUNING MODE CLEAR 1 2 MEMORY Tune into the station that you want to store as a preset. The MEMORY indicator appears and the preset number flashes. Select the preset that you want to delete. While holding down the [MEMORY] button, press the [TUNING MODE] button. The selected preset is deleted and its number disappears from the display. 3 TUNING / PRESET ENTER While the MEMORY indicator is displayed (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 30. In this example, preset #3 is selected. Displaying Radio Information 1 TUNING / PRESET MASTER VOLUME STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR VIDEO 3 INPUT PHONES PURE AUDIO MULTl CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD VIDEO L AUDIO R 4 MEMORY Press the [MEMORY] button again to store the station. The station is stored and the preset number stops flashing. [. . . ] · To control Onkyo components via , point the remote controller at the AV receiver. · To control Onkyo components without , or other manufacturers' components, point the remote controller at that component. · The display is turned off when the Pure Audio (not North American model) listening mode is selected. How do I change the language of a multiplex source? [. . . ]