User manual ONKYO TX-SR505E

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver TX-SR505 TX-SR505E TX-SR8550 TX-SR575 Instruction Manual Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. [. . . ] Muting is cancelled when the AV receiver is set to Standby. DIMMER 46 Common Functions--Continued Using the Sleep Timer With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period. Press the remote controller's [SLEEP] button repeatedly to select the required sleep time. You can set the sleep time from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears. SLEEP indicator Adjusting Speaker Levels You can adjust the volume of each speaker in speaker set A. These temporary adjustments are cancelled when the AV receiver is set to Standby. 1 CH SEL SLEEP Use the remote controller's [CH SEL] button to select each speaker, and use the [LEVEL­] and [LEVEL+] buttons to adjust the volume. You can adjust the volume of each speaker from ­12 dB to +12 dB (­15 dB to +12 dB for the subwoofer). LEVEL- LEVEL+ To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. Notes: · You cannot use this function while the AV receiver is muted. · Speakers that are set to No or None in the Speaker Configuration cannot be adjusted. Speaker Set B While speaker set B is on, you can adjust the volume of the left and right speakers, from ­12 dB to +12 dB. Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack. STANDBY/ON · These settings are stored when the AV receiver is set to Standby. · While speaker set B is on, you cannot adjust the levels of speaker set A's surround back speakers. Headphones While a pair of headphones is connected, you can adjust the volume of each headphone speaker, from ­12 dB to +12 dB each. STANDBY PHONES Notes: · Always turn down the volume before connecting your headphones. · Speaker sets A and B are turned off while the headphones plug is inserted in the PHONES jack. · When you connect a pair of headphones, the listening mode is set to Stereo, unless it was set to Pure Audio, Mono, Stereo, or Direct, in which case it stays the same. · When the multichannel DVD input is selected, only the front left and front right channels can be heard in the headphones. · These settings are stored when the AV receiver is set to Standby. 47 Using the Listening Modes Selecting Listening Modes For a description of each listening mode, see "About the Listening Modes" on page 50. · The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial or optical). · Listening mode availability depends on the format of the current input signal. · While a pair of headphones is connected, you can select only the Pure Audio (not North American model), Mono, Direct, or Stereo listening mode. · The listening modes cannot be selected while speaker set A is off. Selecting with the Remote Controller TV INPUT GUIDE TOP MENU PREVIOUS MENU VOL DISC ALBUM CH VOL SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT SETUP RETURN SURROUND LISTENING MODE STEREO STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY VCR L NIGHT DVD CINE FLTR HDD LEVELLEVEL+ , RC-681M Selecting on the AV Receiver MASTER VOLUME [STEREO] button This button selects the Stereo listening mode. TUNING PRESET STANDBY/ON STANDBY PURE AUDIO PURE AUDIO MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R [SURROUND] button This button selects the Dolby Digital and DTS listening modes and the Neural Surround* listening mode (* TX-SR575 North American model only). LISTENING MODE [ ]/[ ] buttons Pressing these buttons repeatedly cycles through all of the listening modes that can be used with the current input source. A SPEAKERS B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE CLEAR PURE AUDIO STEREO LISTENING MODE [PURE AUDIO] button (not North American model) This button selects the Pure Audio listening mode. When this mode is selected, the AV receiver outputs no video signals and its display is turned off. Pressing this button again will select the previous listening mode. [. . . ] CHECK ANTENNA STANDBY/ON TUNING PRESET STANDBY MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R A SPEAKERS B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE CLEAR SETUP The XM antenna is not properly connected to the Mini-Tuner Dock. UPDATING Positioning the XM Mini-Tuner System You can check the signal strength of the XM radio signal and adjust the position of the XM Mini-Tuner System accordingly. 1 SETUP On the AV receiver, press the [SETUP] button. XM is updating your Mini-Tuner with the latest encryption code. Simply wait a few seconds until the update is done. OR, You may be attempting to tune to a channel that is blocked or that you cannot receive with your subscription package. [. . . ]