User manual ONKYO TX-SR573

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver TX-SR573 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Turning On & First Time Setup. . . . . 30 Basic Operation Playing your AV components . . . . . . . [. . . ] C: LFE channel for subwoofer (1 means yes). MULTI CH 5 Audio from the multichannel DVD input will now be used for the DVD input source. Note: · While the multichannel DVD input is selected, the Speaker Configuration settings on page 32 are ignored, and signals from the multichannel DVD input are fed to the front left, front right, center, surround left, and surround right speakers, and subwoofer as they are. 35 Listening to the Radio Listening to AM/FM Stations TUNING MODE TUNING TUNING / PRESET Manual Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. MASTER VOLUME STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE RETURN SETUP 2 TUNING / PRESET VIDEO 3 INPUT VIDEO L AUDIO R CLEAR PHONES MULTl CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD VCR ENTER TUNER Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. With the built-in tuner, you can enjoy AM and FM radio stations, and store your favorite stations as presets for easy selection. 1 TUNER Use the [TUNER] input selector button to select AM or FM. In this example, FM has been selected. The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. In Manual Tuning mode, FM stations will be in mono. Tuning into Weak FM Stereo Stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Band Frequency (Actual display depends on country. ) Displaying AM/FM Radio Information 1 Tuning into AM/FM Radio Stations TUNING / PRESET MASTER VOLUME Auto Tuning Mode STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE RETURN SETUP 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator appears on the display. CLEAR VIDEO 3 INPUT PHONES MULTl CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD VIDEO L AUDIO R VCR 2 TUNING / PRESET ENTER Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. 1 DISPLAY Press the [DISPLAY] button repeatedly to cycle through the available information. Band, frequency, and preset # When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator also appears. TUNED AUTO Listening mode FM STEREO 36 Listening to the Radio--Continued Listening to XM Satellite Radio® What's XM Satellite Radio?XM offers more than 150 digital channels of audio entertainment, including 100% commercial-free music channels, in the top markets in the U. S. Note: An XM Connect-and-PlayTM antenna and monthly subscription are required to receive XM Satellite Radio. Note: Hardware and required basic monthly subscription sold separately. Premium Channels available at additional monthly cost. Installation costs and other fees and taxes, including a one-time activation fee may apply. All fees and programming subject to change. Channels with frequent explicit language are indicated with an XL. Channel blocking is available for XM radio receivers by calling 1-800XMRADIO. Subscriptions subject to Customer Agreement available at xmradio. com. Only available in the 48 contiguous United States. A warning against reverse engineering: It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE® voice compression software included in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. [. . . ] · With some AV components, certain buttons may not work as expected, and some may not work at all. · To control an Onkyo component that's connected via , point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first (see page 55). · To control an Onkyo component that's not connected via , or another manufacturer's component, point the remote controller at the component. [. . . ]