User manual ONKYO TX-SR602E

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver TX-SR702/702E TX-SR602/602E TX-SR8260 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 First Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Basic Operation . . . . . . . . . . . . . . . . . . . . . . [. . . ] Information is displayed for about three seconds, then the previously displayed information reappears. Interpreting Surround Channel Values A BC A: The number of front channels (3 means front left, front right, and center). B: The number of surround channels (2 means surround left and surround right). If there's surround back channel information, this will be 3. C: LFE channel for subwoofer (1 means yes). 55 Basic Operation--Continued Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. Manual Tuning Mode 1 Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. Listening to the Radio 2 1 Use the [TUNER] input selector button to select either AM or FM. In this example, FM has been selected. Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. Band Frequency (Actual display depends on country. ) The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz steps for AM. In Manual Tuning mode, FM stations will be in mono. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Tuning into Radio Stations 12 Auto Tuning Mode 1 Press the [TUNING MODE] button so that the AUTO indicator appears on the display. 2 Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator appears on the display, as shown. TUNED AUTO FM STEREO 56 Basic Operation--Continued Presetting Radio Stations Deleting Presets 2, 4 3 2 You can store up to 40 of your favorite radio stations as presets. 1 2 1 2 Tune into the station that you want to store as a preset. The MEMORY indicator appears and the preset number flashes. Select the preset that you want to delete. While holding down the [MEMORY] button, press the [TUNING MODE] button. The selected preset is deleted and its number disappears from the display. 3 While the MEMORY indicator is displayed (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 40. In this example, preset #3 is selected. Displaying Radio Information 2 4 Press the [MEMORY] button again to store the station. The station is stored and the preset number stops flashing. Repeat this procedure for all your favorite radio stations. 1 Press the [DISPLAY] button repeatedly to cycle through the available information. Selecting Preset Stations 1 Use the [TUNER] input selector button to select either AM or FM. Band, preset # & frequency Listening mode 2 Use the PRESET [ ]/[ ] buttons, or the remote controller's CH [+/­] button to select a preset. 57 Basic Operation--Continued Using RDS (European models only) RDS only works with European models and only in areas where RDS broadcasts are available. [. . . ] · Only components connected to analog inputs can be played in Zone 2. 92 Troubleshooting--Continued Others The sound changes when I connect my headphones?· When a pair of headphones is connected, the listening mode is set to Stereo, unless it's already set to Stereo, Direct, or Pure Audio (not all models). When you disconnect the headphones, the previous listening mode will be resumed. The speaker volume cannot be set as required? [. . . ]