User manual ONKYO TX-SR800

[. . . ] Contents AV Receiver Before using 2 TX-SR800 Instruction Manual Facilities and connections 8 Setup and operation 29 Thank you for purchasing the Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. Remote controller 61 Appendix 73 E WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Notes: · If you change the input source during recording, you will record the audio signals from the newly selected input source and the video signals assigned to that input source. · You cannot record the surround effects. 38 Setup Menu When making the various settings required to configure your TX-SR800 for optimum performance, you can either use the OSD Menu that appears on your television monitor or you can use the display on the front of the TX-SR800. The OSD Menu is a settings menu that is displayed on your TV monitor. For your reference when performing the setting procedures, this manual shows both the OSD Menu displayed on your television monitor and the display on the front of the TX-SR800. The Setup Menu consists of the Basic Menu that is divided up into 4 menus, the Hardware Setup Menu, Speaker Setup Menu, Input Setup Menu, and Audio Adjust Menu, and the Advanced Menu that contains the menus of the Basic Menu plus the Preference Menu. These menus are then divided up into various sub-menus, and these contain settings for you to optimize your home theater as you wish. The actual contents of your display may differ depending on the model of your region and the selected input source. 0. Hardware Setup 1. Speaker Impedance 0. Hardware Setup 1. Speaker Impedance 2. Surr Back/Zone2 3. IR IN Setup 4. AM Frequency Setup Basic Menu Your TX-SR800 is provided with a Basic Menu for those who are not familiar with many of the advanced settings of an AV receiver or those who wish to watch movies and listen to music with the minimal amount of setup. With the Basic Menu, the settings that rarely need to be set or that are only needed for advanced fine-tuning of the sound quality are not displayed. 2. Surr Back/Zone2 3. IR IN Setup |ENTER|Quit:|SETUP| 1. Speaker Setup 1. Speaker Config 2. Speaker Distance 3. Level Calibration |ENTER|Quit:|SETUP| 1. Speaker Setup 1. Speaker Config 2. Speaker Distance 3. Level Calibration |ENTER|Quit:|SETUP| Basic Menu 0. Hardware Setup 1. Speaker Setup 2. Input Setup 3. Audio Adjust Advanced Menu |ENTER|Quit:|SETUP| |ENTER|Quit:|SETUP| 3. Audio Adjust 1. Tone Control 2. Surround Speakers 2. Input Setup Input:DVD 1. Digital Setup 2. Multichannel Setup 3. Video Setup 4. Character Input 5. IntelliVolume |ENTER|Quit:|SETUP| 2. Input Setup Input:DVD 1. Digital Setup 2. Multichannel Setup 3. Video Setup 4. Character Input 5. IntelliVolume 6. Listening Mode Preset |ENTER|Quit:|SETUP| 3. Audio Adjust 1. Tone Control 2. Surround Speakers 3. Sound Effect 4. Delay 5. LFE Level 6. Mono 7. Theater Dimensional 8. Surround Note: Once you complete the settings in the Hardware Setup Menu, the menu will not appear again when you enter the Basic Menu. 3. Sound Effect default 3. Audio Adjust Advanced Menu The Advanced Menu provides features such as the Listening Mode Presets that allow you to customize the output sound for movies and music just the way you like and the AV Sync Setup that allows you to adjust for discrepancies between the video and audio timing. Settings listed with next to their name are settings that can be set using the Advanced Menu. Advanced Menu 0. Hardware Setup 1. Speaker Setup 2. Input Setup 3. Audio Adjust 4. Preference Basic Menu |ENTER|Quit:|SETUP| 9. THX 10. Mono Movie 11. Enhanced 7 12. Orchestra 13. Unplugged 14. Studio Mix 15. TV Logic default 4. Preference 1. Volume Setup 2. Headphones Level 2. Headphone Level Setup 3. OSD Setup 4. OSD Position |ENTER|Quit:|SETUP| Quit:|SETUP| 39 Setup Menu Advanced Menu 0. Hardware Setup 1. Speaker Setup 2. Input Setup 3. Audio Adjust 4. Preference Basic Menu |ENTER|Quit:|SETUP| 1. Speaker Setup 1. Speaker Config 2. Speaker Distance 3. Level Calibration a. Subwoofer :Yes b. Front :Small c. Center :Small d. Surr L/R :Small e. Surr Back :Small f. Crossover:80Hz(THX) Quit:|SETUP| 1-1. Speaker Config |ENTER|Quit:|SETUP| Main menu Menu Sub-menu Navigating through the Setup Menu You can change settings in the Setup Menu using the buttons on the front panel and on the remote controller. The buttons on the remote controller correspond to those on the TXSR800 as shown below. 1. The main menu (Advanced Menu or Basic Menu) appears on your television monitor. Using the and cursor buttons, select the menu that you want to enter. Press the ENTER button to enter the selected menu. Use the and cursor buttons to select the submenu that you want to enter and press the ENTER button. Each sub-menu has different settings that can be changed as desired, and they are all explained in the pages that follow. To change a setting, first select it using the and cursor buttons, and then change the setting using the and cursor buttons. Press the RETURN button to set the new settings and return to the previous menu screen. Press the RETURN button again to return to the main menu. Note: Press the SETUP button to exit the Setup Menu immediately. Button on remote controller SETUP Button on TX-SR800 SETUP SETUP (upper edge of ENTER button) UP (lower edge of ENTER button) DOWN (left edge of ENTER button) LEFT (right edge of ENTER button) RIGHT ENTER ENTER ENTER RETURN RETURN RETURN 40 Hardware Setup 0. Hardware Setup Menu Advanced Menu 0. Hardware Setup 1. Speaker Impedance 2. Surr Back/Zone2 3. IR IN Setup 4. AM Frequency Step |ENTER|Quit:|SETUP| 0-2. Surr Back/Zone 2 Sub-menu Advanced Menu 0. Hardware Setup 0-2. Surr Back/Zone2 a. Surr Back/Zone2 :Surr Back The settings within the Hardware Setup Menu will need to be made before you use your TX-SR800 for the first time. Once you have selected one of the Hardware Setup menu items, the setting will not be displayed again when you enter the Basic Menu. [. . . ] "Not available in Zone 2 mode" Setting not allowed because the Zone 2 mode is turned on. "Only available with Dolby D" No setting other than Dolby Digital can be set. "Not available in this Listening mode" Will not work with the current listening mode. "Not available with this signal" The listening mode cannot be selected with the current input source. [. . . ]