User manual ONKYO TX-SR804

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver TX-SR804 TX-SR804E Instruction Manual Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Turning On & First Time Setup. . . . . 39 Basic Operation Playing your AV components . . . . . . . [. . . ] You must select Channel Search mode (see page 54). · The following letters are not used in XM Satellite Radio IDs: I, O, S, F. · XM Satellite Radio will transmit a special signal to your AV receiver to activate the full channel lineup. Activation normally takes between 10 and 15 minutes, but during busy peak periods, you may need to leave the AV receiver turned on for up to an hour. 53 Listening to the Radio--Continued 11 -- / --- 10 INPUT SELECTOR MACRO 1 2 3 ZONE2 12 REMOTE MODE RECEIVER RECEIVER TAPE/AMP TV DVD CD HDD TUNER DISPLAY MASTER VOLUME STANDBY/ON STANDBY VCR CABLE CDR SAT MD DIMMER P TO M ENU SLEEP MEN U ZONE 2 + PURE AUDIO MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 TAPE TUNER CD PHONO DISPLAY CH ENTER DISPLAY DISC ALBUM ENTER VOL PREV CH DISPLAY RE TURN U SET PHONES ZONE 2 OFF TONE STEREO DIMMER TUNING MEMORY MODE VIDEO 4 INPUT SETUP RETURN ENTER SETUP MIC P LISTENING MODE ZONE 2 LEVEL CLEAR PRESET TUNING PRESET DIGITAL S VIDEO VIDEO L AUDIO R MUTING / REC PLAYLIST RANDOM RETURN LISTENING MODE STEREO SURR Selecting XM Radio Channels There are two ways to select XM radio channels: · Channel Search mode: select any channel. · Category Search mode: select channels by category. Note: You can't select Channel Search or Category Search mode, while the Tuning Arrow indicators are flashing, as tuning is in progress. Channel Search Mode Selecting XM Channels from the Front Panel: 1 TUNING MODE Press the [TUNING MODE] button to select Channel Search or Category Search mode. 2 ENTER Press the [ENTER] button repeatedly to select a category. 1 ENTER Press the [RECEIVER] button, followed by the [ENTER] button to select Channel Search mode. 3 2 ENTER Use the Up and Down [ ]/[ ] buttons to select a channel. You can also use the Left and Right [ ]/[ ] buttons to select a category. TUNING Use the TUNING Up and Down [ ]/[ ] buttons to select a channel. In Channel Search mode, you can select any channel. In Category Search mode, you can only select channels from the currently selected category. Selecting the Previous Channel: 1 Category Search Mode AV receiver RETURN To listen to the previously selected XM channel, press the [RETURN] button. 1 ENTER Press the [RECEIVER] button, followed by the [ENTER] button to select Category Search mode. Remote controller 2 ENTER Use the Left and Right [ ]/[ ] buttons to select a category, and use the Up and Down [ ]/[ ] buttons to select a channel in that category. 54 Listening to the Radio--Continued Displaying XM Radio Information Press the [DISPLAY] button repeatedly to cycle through the available information. Positioning the XM Antenna You can check the signal strength of the XM Radio signal and adjust the position of the XM antenna accordingly. Channel name 1 RECEIVER Press the [RECEIVER] button, followed by the [SETUP] button. The following information is displayed: 1. Listening mode Note: · If the category, artist, or song title is not available, "- - -" will be displayed instead. Displaying XM Radio Information on Your TV When you select a different XM channel, or the artist or song title changes, the following information is displayed on your TV for 3 seconds. XM 050 CHANNEL: CAT: NAME: TITLE: 5ch Channel name Category name Artist name Song title 2 ENTER Use the Up and Down [ ]/[ ] buttons to select "4. Input Setup, " and then press [ENTER]. 3 ENTER Use the Up and Down [ ]/[ ] buttons to select "3. XM Antenna Aiming, " and then press [ENTER]. Tip: You can display this information at anytime by pressing the [DISPLAY] button. XM Radio Messages The following messages may appear while using XM radio. CHECK ANTENNA 4 Adjust the position of the XM antenna so that the Satellite signal strength bar is as long as possible. 4-3. Antenna Aiming ---------TUNER---------a. Satellite --------------------] [ b. Terrestrial [------------------------------] The XM Mini-Tuner and Home Dock is not connected properly. Check the connection. UPDATING The XM user encryption code is being updated. Please wait. NO SIGNAL The signal is too weak. Check the XM Mini-Tuner and/or antenna connection and reposition it for the best reception. LOADING The main unit is tuning or decoding audio or text data. Please wait. OFF AIR The XM channel you selected is not currently broadcasting. Select another channel. If you can't receive a "Satellite" signal, adjust your XM antenna so that the "Terrestrial" signal strength bar is as long as possible. Terrestrial signals are only available in certain areas. So long as the signal strength is good, you can enjoy XM Radio by using either satellite or terrestrial reception. [. . . ] · The entered remote control code may not be correct. If more than one code is listed, try each one. · If none of the codes work, use the Learning function to learn the commands of the other component's remote controller (page 89). · With some AV components, certain buttons may not work as expected, and some may not work at all. [. . . ]