User manual ONKYO TX-SR8360

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver TX-SR603/603E TX-SR8360 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 First Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Basic Operations . . . . . . . . . . . . . . . . . . . . [. . . ] Use the Down [ ] button to select "Channel, " and then use the Left and Right [ ]/[ ] buttons to select a speaker. 1 2 2­6 1, 7 4 ENTER ENTER 1 RECEIVER Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. 5 ENTER 2 ENTER Use the Up and Down [ ]/[ ] buttons to select "5. Equalizer Settings, " and then press [ENTER]. The Equalizer Settings menu appears. Use the Up and Down [ ]/[ ] buttons to select a frequency, and then use the Left and Right [ ]/[ ] buttons to adjust the level at that frequency. The volume at each frequency can be adjusted from ­6 to +6 dB in 1 dB steps. Tip: Low frequencies (e. g. , 80 Hz) affect bass sounds; high frequencies (e. g. , 8 kHz) affect treble sounds. Use the Up [ ] button to select "Channel, " and then use the Left and Right [ ]/[ ] buttons to select another speaker. The setup menu closes. 6 ENTER 7 Note: This procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button. 51 First Time Setup--Continued Changing the TAPE/MD/CDR Display If you connect an -compatible Onkyo MiniDisc recorder or CD recorder to the TAPE IN/OUT jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. 1, 2 1 TAPE Press the [TAPE] input selector button so that "TAPE" appears on the display. 2 TAPE Press and hold down the [TAPE] input selector button (about 3 seconds) to set the display. Repeat this step to select TAPE, MD, or CDR. 52 Basic Operations Selecting the Input Source This section explains how to select the input source (i. e. , the AV component that you want to listen to or watch). 3 1 1 3 1 1 AV receiver MLUTI CH DVD VIDEO 1 VCR 1 Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], [V3], and [V4] buttons select the VIDEO 1, VIDEO 2, VIDEO 3, and VIDEO 4 input sources, respectively. or VIDEO 2 VIDEO 3 VIDEO 4 VCR 2 TAPE TUNER CD 2 Start playback on the source component. When you select DVD or another video component, on your TV, you'll need to select the video input that's connected to the AV receiver's MONITOR OUT. On some DVD players, you may need to turn on the digital audio output. Remote controller 3 AV receiver MASTER VOLUME or VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The volume can be set to MIN, 1 through 99, or MAX. The AV receiver is designed for home theater enjoyment. It has a wide volume range, allowing precise adjustment. 53 Basic Operations--Continued Using the Sleep Timer With the sleep timer, you can set the AV receiver to turn off automatically after a specified period. Press [RECEIVER] first DIMMER SLEEP SLEEP RECEIVER Press the [RECEIVER] button, and then press the [SLEEP] button repeatedly to select the required sleep time. The sleep time can be set from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears. MUTING Setting the Display Brightness You can adjust the brightness of the display. RECEIVER If you need to cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the time remaining until the AV receiver sleeps, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. DIMMER Press the [RECEIVER] button, and then press the [DIMMER] button repeatedly to select: · Normal+VOLUME light on. [. . . ] When you disconnect the headphones, the previous listening mode will be resumed. The speaker volume cannot be set as required?· When the Automatic Speaker Setup function is used, or the volume is adjusted on the onscreen setup menus, the maximum possible volume setting may change. The speaker distance cannot be set as required? [. . . ]