User manual ONKYO TX-SV313PRO

[. . . ] 45 Listening to the Radio . . . . . . . . . . . . . . . . . . 49 Enjoying the Listening Modes . . . . . 55 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. [. . . ] C: LFE channel for subwoofer (1 means yes). 47 Common Functions--Continued Specifying the Digital Signal Format The following table shows the display indicator for each digital signal format. Format Dolby Digital DTS PCM PCM Display Normally, the AV receiver detects the format of digital input signals automatically. However, if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually. · If the beginnings of tracks from a PCM source are cut off, try the PCM setting. · If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting. MASTER VOLUME STANDBY/ON TUNING PRESET STANDBY ZONE 2 ENTER PURE AUDIO PURE AUDIO MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R ZONE 2 OFF TONE MOVIE/TV MUSIC GAME DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE CLEAR DIGITAL INPUT 1 DIGITAL INPUT Press and hold the AV receiver's [DIGITAL INPUT] button for about 3 seconds. 2 DIGITAL INPUT While "Auto" is displayed (about 3 seconds), press the [DIGITAL INPUT] button repeatedly to select: PCM, DTS, or Auto. PCM: Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and there will be no sound. DTS: Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. Auto (default): The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead. 48 Listening to the Radio AM Frequency Step Setup (on some models) 2 Use the Up and Down [ ]/[ ] buttons to select "0. HardwareSetup, " and then press [ENTER]. 1 2, 3 1, 5 2­4 3 Use the Up and Down [ ]/[ ] buttons to select "AM Freq. " 4 Use the Left and Right [ ]/[ ] buttons to select: 10kHz: Select if 10kHz steps are used in your area. 9kHz: Select if 9kHz steps are used in your area. For AM tuning to work properly, you must specify the AM frequency step used in your area. When tuned to an RDS station, the RDS indicator appears. RDS indicator RDS Program Types (PTY) Type None News reports Current affairs Information Sport Education Drama Culture Display None News Affairs Info Sport Educate Drama Culture Science Varied Pop M Rock M Easy M Light M Classics Other M Weather Finance Children Social Religion Phone In Travel Leisure Jazz Country Nation M Oldies Folk M Document TEST Alarm! What is RDS?RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. RDS is approved by the National Radio Systems Committee (NRSC) and is available in North America. In addition to displaying text information, RDS can also help you find radio stations by type (e. g. , news, sport, rock, etc. ). The AV receiver supports four types of RDS information: PS (Program Service) Science and technology Varied Pop music Rock music Middle of the road music Light classics Serious classics Other music Weather Finance Children's programmes Social affairs Religion Phone in Travel Leisure Jazz music Country music National music Oldies music Folk music Documentary Alarm test Alarm When tuned to an RDS station that's broadcasting PS information, the station's name will be displayed. Pressing the [DISPLAY] button will display the frequency for 3 seconds. RT (Radio Text) When tuned to an RDS station that's broadcasting text information, the text will be shown on the display (see page 54). PTY (Program Type) This allows you to search RDS radio stations by type (see page 54). TP (Traffic Program) This allows you to search for RDS radio stations that broadcast traffic information (see page 54). Notes: · In some cases, the characters displayed on the AV receiver may not be identical to those broadcast by the radio station. Also, unexpected characters may be displayed when unsupported characters are received. · If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all. 53 Listening to the Radio--Continued Displaying Radio Text (RT) RT/PTY/TP MASTER VOLUME 4 ENTER TUNING PRESET ENTER STANDBY/ON STANDBY ZONE 2 PURE AUDIO To start the search, press [ENTER]. The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search. [. . . ] · Make sure that the remote controller is not too far away from the AV receiver and there's no obstruction between the remote controller and the AV receiver's remote control sensor (page 13). · Make sure you've selected the correct remote controller mode. · Make sure you've entered the correct remote control code (page 81). Can't control other components · Make sure you've selected the correct remote controller mode. [. . . ]