User manual ONKYO TX-SV414

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. Read Instructions ­ All the safety and operating instructions should be read before the appliance is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] Note: Speakers that you selected "No" or "None" for in the "Speaker Config" menu will not appear in this menu. Use the and cursor buttons to select "2. Speaker Distance" on the main menu and then press the ENTER button. The "Speaker Distance" menu appears. Use the and cursor buttons to select "Surround Back" and then use the and cursor buttons to set the distance from the surround back speakers to your normal listening position. Press the RETURN button to return to the main menu. Press the MENU button on the front panel or SETUP button on the remote controller button to exit the Setup menu. Calibrating the speaker levels Use this menu to set the volume for each speaker so that each volume is heard by the listener at the same level. This is especially important for speaker layouts where the left and right speakers are at different distances or in asymmetrical positions due to room designs and configurations. These settings and the distance settings performed in the Speaker Distance menu are vital to create the proper sound space and dynamics. Note: The speaker level settings here are not effective for multi-channel input sources. To adjust the speaker levels for multi-channel input sources, you will need to use the CH SEL, LEVEL , and LEVEL buttons on the remote controller. You will hear a pink noise will be emitted from the front left speaker. (1) Remember the volume level of this noise and then press the CH SEL button. The TX-SR700/700E/600/600E will now emit the pink noise from the center speaker. (2) Using the LEVEL / buttons, adjust the volume level of the noise from the center speaker so that it is at the same level as that that was emitted from the front left speaker. The TX-SR700/700E/600/600E will now emit the pink noise from the front right speaker. Use the LEVEL / buttons to adjust the volume of the noise from the front left speaker so that it is the same level as that that was emitted from the center speaker. (4) Use the CH SEL button to select other speakers and adjust the volumes until all speakers are adjusted to the same level. The pink noise level can be adjusted to anywhere between ­12 and +12 decibels for all speakers in 1-decibel increments. Press the TEST button to complete the procedure. (lower edge of ENTER button) Setting the value (left edge of ENTER button) DOWN LEFT (right edge of ENTER button) Selecting the menu ENTER Returning to the previous screen RETURN RIGHT ENTER RETURN 39 Listening to Radio Broadcasts FM MODE TUNING / TUNER One of the features of the TX-SR700/700E/600/600E that is most frequently used is its ability to play FM and AM broadcast radio stations. The TX-SR700/700E/600/600E provides a number of listening modes perfect for listening to the radio and getting the most out of your audio system. Also, by presetting radio stations that you listen to frequently, you can select them easily by pressing the CH button on the remote controller. Listening to a stereo radio station (FM mode) When you tune into a radio station, TUNED indicator appears in the display. [. . . ] · Input source is connected to the COMPONENT VIDEO IN connectors. © Make sure TV (or monitor) is connected to COMPONENT VIDEO OUT connectors (see pages 20, 28). 77 Troubleshooting guide If one of the messages shown below appears "Not available with headphones use" Operation not allowed because headphones are plugged into the TXSR700/700E/600/600E. "Not available with Multichannel use" Operation not allowed while the multi-channel output is being used. "Not available in this Sp Config" Will not work with the current speaker configuration settings. [. . . ]