User manual ONKYO TX-SV424

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. Band Frequency The North American models change FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz steps for AM. In Manual Tuning mode, FM stations will be in mono. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. I Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. (Actual display depends on country) Tuning into Radio Stations 1 12 I Auto Tuning Mode RECEIVER Press the [RECEIVER] button, followed by the [D TUN] button. D TUN 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator appears on the display. (Actual display depends on country. ) The [RECEIVER] button flashes. Within 8 seconds, use the number buttons to enter the frequency of the radio station. For example, to tune to 87. 5 (FM), press 8, 7, 5. Note: While the [RECEIVER] button is flashing, the input source cannot be changed by using the remote controller. 2 2 TUNING PRESET Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. When tuned into a station, the TUNED indicator appears. If "TP" without square brackets appears, this means that the station is not broadcasting TP. To locate a station that is broadcasting TP, press [ENTER]. The AV receiver searches until it finds a station that's broadcasting TP. If no stations are found, the message "Not Found" appears. 3 2 RT/PTY/TP Press the [RT/PTY/TP] button twice. The current program type appears on the display. Use the PRESET [ ]/[ ] buttons to select the type of program you want. See the table on page 54. ENTER ENTER 3 TUNING PRESET 55 Listening to the Radio--Continued Listening to XM Satellite Radio® (North American models only) Important XM Radio Information To receive XM Radio on this receiver you need to purchase an optional XM Passport System and subscribe to XM's paid programming. Please note that XM is currently only licensed to provide service to the contiguous 48 United States (not available in Alaska and Hawaii) and portions of Canada. XM Radio service is not currently available in Mexico or any other region outside the continental U. S. For updates on service availability please visit XM's website at http://www. xmradio. com or http://www. xmradio. ca Note: Hardware and required basic monthly subscription sold separately. Premium Channels available at additional monthly cost. [. . . ] Don't mix different types of batteries, or old and new batteries (page 12). · Make sure that the remote controller is not too far away from the AV receiver, and that there's no obstruction between the remote controller and the AV receiver's remote control sensor (page 12). 89 Troubleshooting--Continued Zone 2 There's no sound · Only components connected to analog inputs can be played in Zone 2. The following settings can be made for the component video, S-Video, and composite video inputs Others The sound changes when I connect my headphones · When a pair of headphones is connected, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct, or Pure Audio (not North American models). The speaker volume cannot be set as required · When the Automatic Speaker Setup function is used, or the volume is adjusted on the onscreen setup menus, the maximum possible volume setting may change. The speaker distance cannot be set as required · In some cases, corrected values suitable for home theater use may be set automatically. [. . . ]