User manual ONKYO TX-SV636

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] (6 m), the Center and Subwoofer distances can be set between 15 and 25 ft. The Surr Right, Surr Left, and Surr Back distances can be set up to 5 ft. For example, if the Front distance is set to 20 ft. (6 m), the Surr Right, Surr Left, and Surr Back distances can be set between 5 and 25 ft. · This procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button. Note: Speakers that you set to No or None on the Speaker Configuration page (page 44) cannot be selected. 47 TXSR603X. book 48 y·[W , Q, O, O, T"N, WOEZ, R"ú·@·. . . --j"ú·@OEßOEã, QZz, Q·ª First Time Setup--Continued Speaker Level Calibration This setting is set automatically by the Automatic Speaker Setup function (see page 38). Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. Note: The speakers cannot be calibrated while the output of the AV receiver is muted, while a pair of headphones is connected, or when using the multichannel input. CD TAPE TUNER 2 ENTER Use the Up and Down [ ]/[ ] buttons to select "3. Level Calibration, " and then press [ENTER]. The Level Calibration menu appears and the pink noise test tone is output by the front left speaker. ENTER 7 +10 8 0 MACRO 9 T V VOL CLEAR 12 11 --/--- 10 INPUT SELECTOR 1 2 3 ZONE2 1 2 REMOTE MODE RECEIVER TAPE/AMP TV VCR CABLE CDR SAT MD DVD CD HDD Note: Speakers that you set to No or None on the Speaker Configuration page (page 44) cannot be selected. DIMMER TO EN PM SLEEP U MEN U + CH DISC ALBUM ENTER VOL 2, 3 1, 5 3 ENTER PREV CH DISPLAY RE TUR N SET UP MUTING Use the Up and Down [ ]/[ ] buttons to select each speaker, and use the Left and Right [ ]/ [ ] buttons to set the volume. The volume can be adjusted from ­12 to +12 dB in 1 dB steps (­15 to +12 dB for the subwoofer). Repeat step 3 until the volume of the test tone from each speaker is the same. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], [V3], and [V4] buttons select the VIDEO 1, VIDEO 2, VIDEO 3, and VIDEO 4 input sources, respectively. or VIDEO 2 VIDEO 3 VIDEO 4 VCR 2 TAPE TUNER CD 2 Start playback on the source component. When you select DVD or another video component, on your TV, you'll need to select the video input that's connected to the AV receiver's MONITOR OUT. On some DVD players, you may need to turn on the digital audio output. Remote controller 3 AV receiver MASTER VOLUME or VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The volume can be set to MIN, 1 through 99, or MAX. The AV receiver is designed for home theater enjoyment. It has a wide volume range, allowing precise adjustment. 51 TXSR603X. book 52 y·[W , Q, O, O, T"N, WOEZ, R"ú·@·. . . --j"ú·@OEßOEã, QZz, Q·ª Basic Operations--Continued 4 CD 5 TAPE 6 TUNER - Using the Sleep Timer With the sleep timer, you can set the AV receiver to turn off automatically after a specified period. Press the [RECEIVER] button, and then press the [SLEEP] button repeatedly to select the required sleep time. The sleep time can be set from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears. [. . . ] · On your recorder, make sure the correct input is selected (e. g. , digital or analog). Zone 2 Zone 2 has turned off?The Sleep function turns off Zone 2 as well as the AV receiver. To set the Sleep function for Zone 2 only, see page 76. · Only components connected to analog inputs can be played in Zone 2. 86 TXSR603X. book 87 ÉyÅ[ÉW ÇQÇOÇOÇTîNÇWåéÇRìÅ@êÖójìÅ@åflå, , ÇQéûÇQïTM Troubleshooting--Continued Others The sound changes when I connect my headphones? [. . . ]