User manual OPTICOM OWB-405

[. . . ] This symbol is intended to alert the user to the presence of unprotected "Dangerous voltage" within the product's enclosure that may be strong enough to cause a risk of electric shock. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE: This equipment has been tested and found to comply with the limits for a class digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at ones own expense. Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. [. . . ] Enter to setup Permissions for each user. Change the ICON with a selected BMP file. Enter to change administrator's password. 19 4. 6. 1 Permission Setup The Account Setup is set to provide individual user (maximum of 4 users) role-based permissions, including access to Setup menu, Network operation, PTZ function, Playback, Utility, Backup and Mask on specific channels while playing back. 4. 7 Network Setup 20 Item Connect type HTTP Setup DDNS Setup Mail Setup Description Setup mode for network connection: ADSL DHCP LAN. Enter to set up HTTP for remote access into DVR. Enter to Enable/ Disable DDNS function and set up. Enter to Enable/ Disable Email notification and setup. 4. 7. 1 Networking Setup The DVR supports DHCP, LAN and ADSL access for network connection. 4. 7. 1. 1 DHCP If the DHCP option is used for DVR network connection, an IP address is assigned by the DHCP server automatically. 21 4. 7. 1. 2 LAN Select LAN for network connection, the following information is required. Item IP Address Subnet Mask Gateway DNS Description Enter IP address provided by ISP Enter IP address of Subnet Mask provided by ISP Enter IP address of Gate way provided by ISP Enter DNS address provided by ISP. (Note: The correct DNS address must be entered for DDNS function). 22 4. 7. 1. 3 ADSL Select ADSL for network connection, the following information is required. Item User Name Password Description Enter user name provided by ISP Enter password provided by ISP 23 4. 7. 2 HTTP Setup Item Enable HTTP Server Port Description Check to enable HTTP server. Users can remotely access into the DVR over the network if the HTTP function is activated. Enter a valid port value from 1 up to 65535. The default value is 80. Quality and Frame Rate Setup for Network Transmission No. Quality FPS Auto Check to activate the transmission of each camera. Choose from Below Basic / Basic/ Normal/ High/ Highest. The maximum recording frames available by the average distribution of each channel (totally 60FPS). This video streaming is used for network transmission; setting is LQ (low quality). Under a low bandwidth capacity, this stream can send out small picture and keep a good video quality and smooth display rate. If the bandwidth is large enough, it can be adjusted to HQ (high quality). Thus, the network streaming will be switched to the condition which this DVR is recording. Therefore, a larger video image can be sent to remote site. 24 4. 7. 3 DDNS Setup Item Enable DDNS DDNS Server Host Name User Name Password Description Check/ Uncheck to Enable/ Disable DDNS function. Enter password. 4. 7. 4 Mail Setup 25 E-mail can be used as a form of notification when an event occurs (VLOSS, MOTION, and SENSOR). Item Enable E-mail Notification SMTP Server User Name Password Sender E-mail Trigger Event Receiver E-mail Description Check the box to enable/disable E-mail Notification function. Enter to set up e-mail address of sender. [. . . ] (Note: Please initialize your newly-installed HDD before using it, otherwise it can be recognized as BAD by the DVR). The latest format time of HDD 35 Chapter 5 SEARCH & BACKUP 5. 1 Search Setup Item Event Search Time Search Description Press to enter event search menu. Press to enter time search menu. 5. 1. 1 Event Search 36 The DVR automatically records events with type, time and channel information included. If there is recording data for an event, a yellow signal icon will be shown on the left side of time information. [. . . ]