User manual OPTICON MDI 2000

[. . . ] Auto-focus Imager Engine MDI 2000 This manual provides specifications for the MDI 2000 2D imager scan engine with auto-focus. Specifications Manual Opticon MDI 2000 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: MDI 2000 1 2009-04-26 Specification Number: Original Spec Number: Copyright 2009 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. [. . . ] The MDI 2000 includes the following features: · High-Speed Scanning Customized High-speed/ultra-sensitive CMOS image sensor at the maximum of 80 fps and the fastest shutter speed in the industry enable high-speed scanning without being affected by hand movement. Reading both high resolution and super deep barcodes With an embedded liquid lens in the scan engine, the MDI 2000 is able to read both high resolution and super deep barcodes. High-Speed Auto-Focus High-speed CMOS image sensor uses laser light for distance range to enable highspeed auto-focus. When environmental conditions make using distance range with laser light impossible, focus adjustment will be done using the contrast method. Note: , and respectively represent pitch, skew and tilt. Please see section 6 for how these values are defined. 7 Opticon MDI 2000 Specifications Manual 5. Absolute Maximum Ratings Parameter Power supply voltage (VCC to GND) Input voltage Output current Symbol VCC VIN IO Value 3. 9 -0. 3 to V +0. 3 ±4 Unit V V mA 5. 2. Recommended Operating Conditions Item Power supply voltage1 Rush current peak Input voltage Output voltage 2 Symbol VCC IPK VIH VIL VOH VOL Min 3. 15 Typ 3. 3 6 Max 3. 45 7 VCC +0. 3 0. 9 Unit A V V V Conditions H level L level H level L level 2. 4 -0. 3 2. 8 - 0. 5 IOH=-4mA IOL= 4mA V 5. 3. Consumption Current with Default Settings When the scan engine is configured to "Prior snapshot ON" and "Snapshot and decoding parallelism ON. " Parameter Operating current Stand-by current Power-down current 3 Symbol IOP ISTB TSLP Min -- -- -- Typ 300 175 25 Max 350 250 70 Unit mA mA mA 5. 4. Consumption Current with Standard Scanning Mode When the scan engine is configured to "Prior snapshot OFF" and "Snapshot and decoding parallelism OFF. " Parameter Operating current Stand-by current Power-down current 4 Symbol IOP ISTB TSLP Min -- -- -- Typ 250 90 10 Max 390 110 25 Unit mA mA mA Input connector. VCC is supplied by a direct-current power of 10 A, measured using a current probe. If it is necessary to decrease the impressed current, please supply the power slowly. 3 When configured with the SLEEP command or power-down mode. 4 When configured with the SLEEP command or power-down mode. 2 1 8 Opticon MDI 2000 Specifications Manual 5. 5. Power Mode Transition Power On Enable AIM/WUPn Signal Standby Sleep Command or Power Down Mode Power Down Enable TRIGn Signal or Scanning Command Completion of Scanning or Scanning Time-out Enable TRIGn Signal Scan Figure 1: Power mode transition When in Power Down mode, the MDI 2000 automatically enters the powered-down state from Power On. When the MDI 2000 is in Power Down mode, the MDI 2000 is switched to Standby mode by receiving the AIM/WUPn signal. If there is no event to switch the MDI 2000 to other modes after the AIM/WUPn signal is turned off, the MDI 2000 enters Power Down mode again after the Standby mode times out. If the MDI 2000 enters a powered-down state while using a USB COM interface, it may cause defects with the operation of a Windows device driver. 9 Opticon MDI 2000 Specifications Manual 6. Imager Scanning Parameter Scan method Scan rate Range of readable pixels Light emitting element for aiming/distance ranging (Laser diode) Peak wavelength Maximum radiation output Auxiliary LED for lighting (LED 1) Peak wave length Directivity angle 2 ½ Maximum radiation output View angle (approximate) Specification CMOS area sensor (Black and white) 80 900 (H) x 512 (V) Red laser diode 650 1 InGalP Red LED 645 60 5040 Horizontal: 40 Vertical: 23 Unit -- fps pixel nm mW nm ° mcd ° 6. 2. Imager Output Item Image data format Shades of gray Range of output image Resolution of output image Interface of output image Transmission time Specification Windows Bitmap, JPEG, TIFF 256, 16, 2 Select in horizontal and vertical scale. Full, 1/2, 1/3, 1/4 RS-232C, USB-VCP USB-VCP (Full speed) RS-232C (115. 2 kbps) Conditions: Shades of gray: 256 Resolution: full About 4 sec About 120 sec 10 Opticon MDI 2000 Specifications Manual 6. 3. Auto Focus The imager scan engine requires 100 ms to capture the image with auto focus after trigger ON. [. . . ] JIS C6802: 2005: Laser class 2 IEC 825-1/EN 60825-1: Laser class 2 FDA CDRH Laser class II. Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations pursuant to laser notice No. Class II laser devices are not considered to be hazardous when used for their intended purpose. Avoid staring into the laser beam. 14. 2. [. . . ]