User manual OPTICON OPL 7836

[. . . ] Handheld Laser Barcode Scanner OPL 7836 The OPL 7836 is a handheld laser barcode scanner. Specifications Manual Opticon OPL 7836 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: OPL 7836 2A 2007-02-01 Specification Number: Original Spec Number: SS06100 SS06078 Copyright 2007 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. [. . . ] Note: , and respectively represent pitch, skew and tilt. Please see section 7 for how these values are defined. 8 Opticon OPL 7836 Specifications Manual 5. Electrical Characteristics Parameter Power supply voltage Operating current Rush current peak Stand-by current Startup time Symbol VDD IOP IPEEK IPRE TD Min 4. 5 - Typ 5. 0 85 450 35 100 Max 5. 5 150 500 70 - Unit V mA mA mA ms Remarks Buzzer Off Conditions · · · Connect 1 resistance to a power supply line in series and measure the current by the voltage between both ends of resistance. Power supply voltage is measured at a connector terminal area. The current value depends on the interface type and host computer to which the device is connected. 6. Laser Scan Specifications Parameter Light-emitting element Emission wavelength Light output Scanning method Scanning speed Scan angle Specification Red laser diode 650 ±10 (25° C) 1. 0 or less Bi-directional scanning 100 ±20 Scan angle: 54 ±5 Read angle: 44 (Min) Unit -- nm mW -- scans/s ° ° Notes: Refer to chapter 15, "Trigger and Read Options, " to read about the scan modes. Refer to chapter 7, "Technical Specifications, " to read about scanning performance. Tilt of Laser Scan Line Maximum tilt between both ends of a laser scan line. Less than 1. 2° upward tilt from the scan origin. Maximum of 3. 1 mm when measured at the point 150 mm away from the scan origin. (Measurement was done from the center of the scan line. 9 Opticon OPL 7836 Specifications Manual 6. 1. 2. Curvature of Scan Maximum gap between the straight line connecting both ends of the laser scan line and the actual laser scan line. Less than 1. 27° curvature from the scan origin. Maximum of 3. 3 mm when measured at the point 150 mm away from scan origin. (Measured from the center of the scan line. ) Figure 1:Laser scan tilt and curvature 7. Technical Specifications The conditions for technical specifications are as follows, unless otherwise specified in each section. Conditions Ambient temperature and humidity: Ambient light: Background: Room temperature (5 to 35º C) Room humidity (45% to 85% RH) 500 to 900 lx Barcode = black Space = white Margin = white Background of label = black 5. 0 V Approve the performance when decoding is successful in all ten tests. (Decoding is deemed successful when completed in 0. 5 seconds or less. ) Power supply voltage: Decoding test: 7. 1. Print Contrast Signal (PCS) 0. 45 or higher (over 70% of reflectivity of space and quiet zone). PCS= Reflectance of white barReflectance of black bar Reflectance of white bar Scanning performance may decline if dirt or scratches mar the optical window. Minimum Resolution 0. 127 mm 10 Opticon OPL 7836 Specifications Manual 7. 3. Depth of Field The depth of field is measured from the edge of the scanner. [. . . ] JIS C6802: 2005: Laser class 2 IEC 825-1/EN 60825-1: Laser class 2 FDA CDRH Laser class II. Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations pursuant to laser notice No. Class II laser devices are not considered to be hazardous when used for their intended purpose. Avoid staring into the laser beam. 16. 2. [. . . ]