User manual OPTICON OPR 3201

[. . . ] Gun-type Laser Barcode Scanner OPR 3201 The OPR 3201 is a gun-Type laser barcode scanner that uses a short-wavelength red laser beam to enhance the visibility of scanning lines. The decoded text of barcode images is output through an RS-232C, USB, or Wedge interface. Specifications Manual Opticon OPR 3201 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: OPR 3201 1A 2009-08-31 Specification Number: Original Spec Number: SS07067 SS07040 Copyright 2009 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. [. . . ] Configuration The OPR 3201 consists of a laser module (which includes a scan mirror, a coil, and a photo diode), a decode and communication section (which decodes scanned data and carries out signal processing), a 3. 3 V power supply, an interface (which outputs decoded data), a buzzer, LEDs, and a trigger key. The OPR 3201 RS-232C model operates on a DC 6. 0 V power supply fed from the dedicated adapter. USB and Wedge models operate on bus power, so those models do not use an adapter. Figure 2: OPR 3201 configuration 10 Opticon OPR 3201 Specifications Manual 6. 2. Electrical Characteristics Interface Parameter Operating voltage RS-232C Operating current Rush current Stand-by current Operating voltage USB Wedge Operating current Rush current Stand-by current Min 4. 5 -- -- -- 4. 5 -- -- -- Typ 6. 0 100 550 35 5. 0 100 450 35 Max 6. 6 160 600 65 5. 5 160 500 65 Unit V mA mA mA V mA mA mA Notes 100 mA--Laser: ON, Buzzer: OFF 160 mA--Laser: ON, Buzzer /LED:ON Power supply voltage: 6. 0 V Auto trigger OFF/ON 100 mA--Laser: ON, Buzzer: OFF 160 mA--Laser: ON, Buzzer /LED:ON Power supply voltage: 5. 0 V Auto trigger OFF/ON Conditions Connect 1 resistance to a power supply line in series and measure the current by the voltage between both ends of resistance. Power supply voltage is measured at a connector terminal area. The current value depends on the interface type and host computer to which the device is connected. 6. 3. AC Adapter The OPR 3201 with RS-232C serial interface is shipped with a dedicated AC adapter "Universal AC Adapter Kit. " Plug connectors can be changed for each region. See diagrams below. Item Model Name Dimensions DC output cable length Voltage range Input specifications Supply current Voltage range Output Specifications Operating temperature Maximum current Specification SFP0602000P-PSE 47. 5 (W) × 28. 0 (D) × 75. 0 (H) mm 1. 8m AC 90 to 265 V 0. 5 A max 5. 7 to 6. 3 V 2 A max 0 to 40° 11 Opticon OPR 3201 Specifications Manual 6. 3. 1. AC Input Dimensions: 47. 5 (W) × 28. 0 (D) × 75. 0 (H) mm (except protruding portion) Figure 3: AC adapter 1 6. 3. 2. DC Output Figure 4: AC adapter 2 7. Laser Scan Specifications Parameter Light-emitting element Emission wavelength Light output Scanning method Scanning speed Scan angle Specification Red laser diode 650 ±10 (25° C) 1. 0 or less Bi-directional scanning 100 ±20 Scan angle: 54 ±5 Read angle: 44 (Min) Unit -- nm mW -- scans/s ° ° Notes: Refer to chapter 16, "Trigger and Read Options, " to read about the scan modes. 12 Opticon OPR 3201 Specifications Manual Refer to chapter 8, "Technical Specifications, " to read about scanning performance. Tilt of Laser Scan Line Laser scanning tilt is the vertical difference between both ends of a laser scan line. Measure it in the middle of the laser scan line. · Up to 0. 92° angle in vertical direction from the scan origin (mirror motor). · Up to 2. 46 mm when measured at a point 150 mm from the scan origin. 7. 1. 2. Curvature of Scan The maximum difference between the laser scan line and the line between both ends of the laser scan line. Measure it in the middle of the laser scan line. · Up to 1. 27° angle in vertical direction from the scan origin (mirror motor). · Up to 3. 3 mm curvature when measured at a point 150 mm away from the scan origin. Figure 5: Laser scan tilt and curvature 13 Opticon OPR 3201 Specifications Manual 8. Technical Specifications The conditions for technical specifications are as follows, unless otherwise specified in each section. Conditions Ambient temperature and humidity: Ambient light: Background: Room temperature (5 to 35º C) Room humidity (45% to 85% RH) 500 to 900 lx Barcode = black Space = white Margin = white Background of label = black 6. 0 V (RS-232C) 5. 0 V (USB and Wedge) Approve the performance when decoding is successful in all ten tests. (Decoding is deemed successful when completed in 0. 5 seconds or less. ) Power supply voltage: Decoding test: 8. 1. [. . . ] JIS C6802: 2005: Laser class 2 IEC 825-1/EN 60825-1: Laser class 2 FDA CDRH Laser class II. Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations pursuant to laser notice No. Class II laser devices are not considered to be hazardous when used for their intended purpose. Avoid staring into the laser beam. 17. 2. [. . . ]