User manual OPTICON OPV 1001

[. . . ] Laser Multi-barcode Scanner OPV 1001 The OPV 1001 is a 1000 scans multi-barcode laser scanner reading for omni-directional reading. Specifications Manual Opticon OPV 1001 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: OPV 1001 6 2008-04-07 Specification Number: Original Spec Number: SS06175 SS06172 Copyright 2008 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. [. . . ] The current value depends on the interface type and the host computer to which the device is connected. 5. 2. AC Adapter Input: Input voltage Power supply frequency Maximum current Rush current Output: Output voltage Output ripple Maximum current Startup time DC 5 V ±5% (6 V also supported) up to 100 mVp-p 2000 mA up to 20 ms (AC100V/50 Hz, 5% to 95% of output voltage) AC 90 V to 264 V 47 Hz to 63 Hz up to 400 mA (at 100 V AC/50 Hz) up to 70 A 5. 3. Red · · Lights up when any unsupported menu is read in the menu mode (200 ms with error buzzer). Blinks when motor failure occurs (indefinitely). 5. 3. 2. Green · Good read: when reading is done successfully. 9 Opticon OPV 1001 Specifications Manual 6. Laser Scan Specifications Parameter Light-emitting element Emission wavelength Light output Scanning method Scanning speed Specification Red laser diode 650 ±10 (25° C) 1. 0 or less (measured at the front of the scanner's plastic mask) Rastering omni-directional scanning 1000 ±50 Unit ­ nm mW ­ scans/s 7. Technical Specifications The conditions for technical specifications are as follows, unless otherwise specified in each section. Conditions Ambient temperature and humidity: Ambient light: Background: Room temperature (5 to 35º C) Room humidity (45% to 85% RH) 500 to 1000 lx Barcode = black Space = white Margin = white Background of label = black 5. 0 V Approve the performance when decoding is successful in all ten tests. (Decoding is deemed successful when completed in 0. 5 seconds or less. ) Power supply voltage: Decoding test: 7. 1. Print Contrast Signal (PCS) 0. 45 or higher (over 70% of reflectivity of space and quiet zone). PCS= Reflectance of white barReflectance of black bar Reflectance of white bar Scanning performance may decline if dirt or scratches mar the optical window. Minimum Resolution 0. 127 mm 10 Opticon OPV 1001 Specifications Manual 7. 3. Scan Area The scannable area depends on the barcode type (PCS, resolution, length, etc. ) and the direction of the barcode surface. However, the barcode should be set within the following area. Figure 1: Scan area Note: Binary codes are more likely to cause scanning errors than multi-level codes. To minimize problems, fix the length of binary codes. Depth of Field The depth of field is measured from the edge of the scanner. The scanning range is within the circular arc centered on the scan origin. 11 Opticon OPV 1001 Specifications Manual Figure 2: Depth of field PCS 0. 9 0. 9 0. 9 or higher 0. 9 Resolution (mm) 0. 66 0. 33 0. 2 0. 127 Decode Depth (mm) 70 - 230 15 - 200 15 - 110 15 - 50 Resolution (mm) 0. 66 0. 33 0. 2 0. 127 Symbology JAN-8 JAN-13 Code 39 Code 39 Digit 8 13 7 4 Barcode Sample OPTOELECTRONICS Test Sample OPTOELECTRONICS Test Sample Laser printer labels OPTOELECTRONICS Test Sample Conditions Barcode Sample: OPTOELECTRONICS Test Sample N/W Ratio: Angle: Curvature: 1:2. 5 = 0°, = 15°, = 0° R= 12 Opticon OPV 1001 Specifications Manual 7. 4. Pitch Angle = ±35° Figure 3: Pitch 7. 4. 2. Skew Angle and Dead Zone Skew angle: = ±50° (Excluding dead zone) Dead zone: = ±8° (There are some areas in which decoding fails due to specular reflection) Figure 4: Skew and dead zone 13 Opticon OPV 1001 Specifications Manual 7. 4. 3. Tilt = 360° There are some angles at which decoding fails, depending on the height of a barcode. Figure 5: Tilt Conditions Barcode Sample: OPTOELECTRONICS Test Sample Distance: Label: 70 mm from the front edge of the scanner Pitch, Skew Angle PCS = 0. 9, Resolution = 0. 33 mm, Symbology = JAN-13 Position The center of the barcode and the scan line are almost the same (refer to the following figure). Curvature: = , skew angle = +10°(for measuring pitch angle and tilt angle) Angle: Note: The specifications are decided on one horizontal scan line, except Tilt. 14 Opticon OPV 1001 Specifications Manual 7. 5. Curvature With 8-digit JAN/UPC/EAN barcodes, decoding performance is guaranteed when R20 mm. [. . . ] Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations pursuant to laser notice No. Class 1 laser devices are not considered to be hazardous when used for their intended purpose. Avoid staring into the laser beam. 18. 2. Product Safety EN60950-1: 2001 IEC60950-1: 2001 18. 3. [. . . ]