User manual OPTICON PHL 1300

[. . . ] User's Manual Pocket Terminal PHL1300 Cradle IRU1300 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE CAUTION: This user's manual may be revised or withdrawn at any time without prior notice. Copyright 2002, Opticon Sensors Europe B. V. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon Sensors Europe. Limited warranty and disclaimers By opening the package of this product you agree to become bound by the liability and warranty conditions as described below. [. . . ] Terminal on cradle Take notice that the IRU1300 cradle is designed for the PHL1300 terminal. No other types of terminals can be placed into this cradle. 1 2 3 4 Start with a full battery To be sure of proper operation, it is advised to start with a full battery, charge the battery pack according to the instructions in the next chapter. Click the battery pack into the terminal, as instructed in the next chapter. 10 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE 2. 5 INSTALLING, REPLACING AND CHARGING BATTERIES Wrong use of batteries might cause serious damage to the terminal or to the cradle. In order to avoid damage it is very important to take notice of the instructions. ! Insert full batteries before use of the terminal. Never remove the main battery pack while the terminal is turned on. Doing so can cause data in the terminal to be deleted. Never change the main battery pack while the backup battery is out. When you do not use the terminal for a long time, make sure the main battery has enough capacity. 3) Make sure you use the right battery size. Place 2 batteries in the battery holder aligning plus (+) and minus (-) ends as shown inside the battery compartment. Lock main battery case cover: Position the case cover and fix its position by screwing hand tight. 2. 5. 2 How to charge the rechargeable battery pack in the cradle? Make sure that the Opticon rechargeable battery pack is inserted in the terminal. If the terminal with the battery pack is placed in the cradle, the LED on the cradle will turn green. When the terminal is placed in the cradle, the rechargeable battery pack will be charged automatically for 8 hours. 2. 5. 3 When to replace or recharge the main battery? There are 2 reasons for replacing the main battery; as soon as possible after the battery indicator appears on the display. when you are not using the terminal for an extended period. 2. 5. 4 When to replace the backup battery? When low battery mark appears, replace the battery without delay. 12 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE 2. 5. 6 How to (re) place the backup battery in the terminal? ! Make sure that the main battery is full enough while changing the backup battery. Only use CR2032 Li (Lithium, button type) battery. ! Unlock backup battery case cover: (ref. a) Unlock the case cover by use of a small crosshead screwdriver or swatch screwdriver. Remove old battery by simply taking out. b) Make sure that the positive side of the battery is pointed upwards (visible) and place it in the compartment. Lock backup battery case cover: Position the case cover and fix its position by screwing hand tight. 1 2 3 a b 13 USER'S MANUAL PHL1300 TERMINAL / IRU1300 CRADLE 2. 6 INSTALLING IN A SYSTEM ! Exercise caution at all times when working with AC-powered equipment. Turn off your devices before installation. Because of the special pin-out of the connectors, use the cables supplied by the manufacturer. When you need another cable for a certain device, that is not supplied, contact your supplier to purchase the right cable. [. . . ] Clean the optical interface window of the cradle and/or terminal, and try again. When the power indicator is still not green, the cradle needs service. The resolution of the bar code is too high. Decrease the distance between the bar code and the terminal. ? The angle between the label and the terminal is too high. Change the angle between the bar code and the terminal. ? No data transmitted The cradle will only work if connected to a PC. [. . . ]