User manual OPTOMA HD72

[. . . ] Table of contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Usage Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press "Zoom" button to zoom in and zoom out of image. Select the display mode from Cinema, Bright, TV, sRGB and User. Press "Menu" to launch the on-screen display (OSD) menu. To exit OSD, Press "Menu" again. Use to select items or make adjustments to your selection. Mask off a few pixels on each edge of the image to be displayed. Use this function to adjust if image source happens to have noise near any edge of the display image. The input source will be displayed without scaling. Enable the viewing of the letterboxed nonanamorphically enhanced movie at full screen width. Part of the original image will be lost if the image aspect ratio is less than 1. 78:1. V. Keystone / Zoom Display Mode Menu Four Directional Select Keys Select (Enter) Overscan 4:3 16:9 Native Letter-Box 18 User Controls DVI-D DVI-A HDMI YPbPr Video S-Video Press "DVI-D" to choose Digital Signal source from DVI-I connector. Press "HDMI" to choose source from HDMI connector. Press "YPbPr" to choose Component video source. Press "Video" to choose Composite video source. Press "S-Video" to choose S-video source. 19 English Press "DVI-A" to choose Analog Signal source from DVI-I connector. User Controls On-screen Display Menus The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press "Menu" on the Remote Control or Control Panel. 2 When OSD is displayed, use keys to select any item in the main menu. While making a selection on a particular page, press or "Select (Enter)" key to enter sub menu. 3. Use settings by keys to select the desired item and adjust the key. 4. Select the next item to be adjusted in the sub menu and adjust as described above. 5. Press "Select (Enter)" to confirm, and the screen will return to the main menu. 6. The OSD menu will close and the projector will automatically save the new settings. Main Menu Sub Menu Setting 20 User Controls Menu Tree English 21 User Controls Image Mode There are many factory presets optimized for various types of images. Cinema: For home theater. [. . . ] Move to within 6 m (20 ft) of the projector. Make sure batteries are inserted correctly. If so, replace weak batteries in the remote control. 38 Appendices Replacing the lamp English 3 1 The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. Warning: Lamp compartment is hot! [. . . ]