User manual OPTOMA HD7300

[. . . ] Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Certain versions of the HD3000 have been factory preset for a single output range. Input Configurations · Front Panel 2 3 1 Up IN 3 Left VIDEO S-VIDEO VGA IN Right/ Re-sync Down Menu/ Exit Enter/ Source On / Standby 1 : VGA 2 : S-video 3 (NTSC, PAL and SECAM) 3 : Composite 3/CVBS 3 (NTSC, PAL and SECAM) HD3000 User's Guide 7 Professional Video Scaler and Color Management System HD3000 User's Guide · Back Panel 4 7 9 11 13 21 22 5 IN 1 VIDEO S-VIDEO Y Pb Pr DC-12V G/Y B/Pb R/Pr H V HDMI IN-1 HDMI IN-2 HDMI IN-3 RS-232 To AV receiver From AV receiver IR Module To display AC IN IN 2 COMPONENT IN BNC IN HDMI SWITCH 6 8 10 12 14 15 17 16 18 19 20 4: AC IN 5: Composite 1/CVBS 1 (NTSC, PAL and SECAM) 6: Composite 2/CVBS 2 (NTSC, PAL and SECAM) 7: S-video 1 (NTSC, PAL and SECAM) 8: S-video 2 (NTSC, PAL and SECAM) 9: Component YPbPr/BNC 1 (NTSC, PAL and SECAM, 480i/p, 576p, 720p and 1080i) 10: Component YPbPr/BNC 2 (NTSC, PAL and SECAM, 480i/p, 576p, 720p and 1080i) 11: DC 12V OUTPUT 12: DC 12V OUTPUT 13: YPbPr/RGBHV 1 (NTSC, PAL and SECAM, 480i/p, 576i/p, 720p and 1080i) 14: YPbPr/RGBHV 2 (NTSC, PAL and SECAM, 480i/p, 576i/p, 720p and 1080i) 15: HDMI 1 (480i/p, 576i/p, 720p and 1080i) 16: HDMI 2 (480i/p, 576i/p, 720p and 1080i) 17: HDMI 3 (NTSC, PAL and SECAM, 480p, 576p, 720p, 1080i) 18: HDMI TO AV RECEIVER 19: HDMI FROM AV RECEIVER 20: TO DISPLAY 21: RS232 22: IR Module Connecting HD3000 To AV Reciever For maximum flexibility when integrating into existing entertainment systems, the HD3000 Video Scaler is equipped with 2 HDMI outputs. One output directly sends the signal out to the display and the second output sends the signal out to an HDMI equipped AV receiver. There are three ways to connect the HDMI output from the HD3000 Video Scaler. Option 1 Using HD3000 Video Scaler as video source selector and HDMI equipped AV Receiver for audio: HD3000 User's Guide 8 Professional Video Scaler and Color Management System HD3000 User's Guide If you have an HDMI equipped AV receiver and wish to send the audio signal to the receiver, but utilize the HD3000 as the video source selector: 1) Connect the video sources to the HD3000. 2) Attach an HDMI cable to the "To AV Receiver" port on the back of the HD 3000. Connect the other end to your AV Receiver. This will allow the audio signal to be controlled by the AV Receiver. 3) Attach a 2nd HDMI cable to the AV out port on the back of the AV Receiver. Connect the other end to the "From AV Receiver" on the back of the HD3000. This will return the video signal in a "pass through" mode. 4) Finally, connect an HDMI Cable to the "To Display" on the back of the HD3000. Connect the other end to your display projector. Option Using HD3000 as video source selector and directly connecting the video source to the AV Receiver: If you do not have an HDMI equipped AV receiver, to ensure proper audio connections, you will need to directly connect the Audio out from the Video source to your receiver. The HD3000 User's Guide 9 Professional Video Scaler and Color Management System HD3000 User's Guide HD3000 will be used only to process the Video signals. 1) Connect the video sources to the HD3000. 2) Connect the video sources audio out directly to your receiver. 3) Attach the short HDMI cable that comes standard with the unit to the "To AV Receiver" port on the back of the HD 3000. Connect the other end to the "From AV Receiver" port on the back of the HD3000. This will allow the video signal to be properly managed. 4) Finally, connect an HDMI Cable to the "To Display" on the back of the HD3000. Connect the other end to your display projector. Option 3 If you have a single HDMI source, you can hook the Video source directly up to the "From AV Receiver" port on the back of the HD3000. Connect a second HDMI cable to the "To Display" port on the back of the HD3000 and attach the other end to your Plasma TV or Projector display system. This configuration will provide the 2. 1 audio and high resolution video for your display. HD3000 User's Guide 10 Professional Video Scaler and Color Management System HD3000 User's Guide Establishing Initial Output Resolution From the factory, the HD3000 is shipped with the default output resolution of 1280x720, progressive scan, commonly knows as 720p. [. . . ] If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code information is provided regarding the proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrodes. For additional safety during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the receiver due to lightning and power-line surges. [. . . ]