User manual OREGON SCIENTIFIC BAR289

[. . . ] Jumbo Weather Station with Remote Control Model: BAR289 User Manual BAR289 Cover R7 OP Black 1 8/20/04, 11:00 PM Jumbo Weather Station with Remote Control Model: BAR289 User Manual INTRODUCTION Thank you for selecting the Oregon ScientificTM Jumbo Weather Station with Remote Control (BAR289). This powerful device bundles time keeping, weather forecast, indoor and outdoor temperature, with remote control facility, into a single tool you can use from the convenience of your home. In this box, you will find: · · · · · · Main unit (BAR289) Remote control (RE289) Remote sensor (RTHR328N) Main unit batteries, 4 x UM-3 (AA) 1. 5V Remote control batteries, 2 x UM-4 (AAA) 1. 5V Remote sensor batteries, 2 x UM-3 (AA) 1. 5V CONTENTS Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Fold-out stand 1 REMOTE SENSOR (RTHR328N) - LCD DISPLAY 2 3 1. Temperature reading 4 BAR289 ENG R7 OP Black 4 8/20/04, 11:00 PM GETTING STARTED BATTERIES Batteries are supplied with this product: · · · Main unit Remote control Remote sensor 4 x UM-3 (AA) 1. 5V 2 x UM-4 (AAA) 1. 5V 2 x UM-3 (AA) 1. 5V SENSOR SET UP 1. Open the battery compartment with a small Phillips screwdriver and insert the batteries matching the polarity (+ and -) as shown below. Insert batteries before first use, matching the polarity as shown in the battery compartment. For best results, install batteries in the remote sensor before the main unit. Set the channel by pressing the CHANNEL button to the required number. If you are using more than one sensor, select a different channel for each sensor. Slide the EU / UK switch to the setting which best suits your location. Press SEARCH to manually initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor. (Refer to the "Sensor Data Transmission" section for more information. ) 7. Press the °C / °F button to select the setting you want. Close the remote sensor battery compartment. Secure the sensor in the desired location using the wall mount or table stand. To fold out the stand: To install the remote control batteries: 1 NOTE Do not use rechargeable batteries. UNIT Main Remote Sensor LOCATION Clock / Alarm / Calendar Area Outdoor Temperature Area For best results: · Insert the batteries and select the unit, channel, and radio signal format before you mount the sensor. · Place the sensor out of direct sunlight and moisture. · Do not place the sensor more than 30 metres (100 feet) from the main (indoor) unit. · Position the sensor so that it faces the main (indoor) unit, minimizing obstructions such as doors, walls, and furniture. · Place the sensor in a location with a clear view to the sky, away from metallic or electronic objects. · Position the sensor close to the main unit during cold winter months as below-freezing temperatures may affect battery performance and signal transmission. NOTE The transmission range may vary and is subject to the receiving range of the main unit. You may need to experiment with various locations to get the best results. 2 NOTE It is recommended that you use alkaline batteries with this product for longer performance. REMOTE SENSOR (RTHR328N) This product is shipped with the RTHR328N Remote Sensor. [. . . ] MAXIMUM / MINIMUM RECORDS · · Press MEMORY to toggle between maximum (MAX), minimum (MIN) and current records. To clear the records, press and hold MEMORY for 2 seconds. A beep will sound to confirm that the memory has been cleared. · · · · NOTE The sensor auto-search function cannot be operated by the remote control. NOTE The main unit must be no more than 4 metres (13 feet) from the remote control for a successful connection to take place. [. . . ]