User manual OREGON SCIENTIFIC BAR628HG-EASY WEATHER STATION ADVANCED

[. . . ] INTRODUCTION Thank you for selecting the Oregon ScientificTM Weather Station Advanced (BAR628HG / BAR628HGU). This device bundles precise time keeping, weather forecast, and indoor and outdoor temperature and humidity monitoring features into a single tool you can use from the convenience of your home. In this box, you will find: · · · · Main unit Remote sensor (THGR122NX) Main unit batteries, 3 x UM-3 (AA) 1. 5V Remote sensor batteries, 2 x UM-4 (AAA) 1. 5V Weather Station Advanced Model: BAR628HG / BAR628HGU User Manual CONTENTS Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 4. Wall mount hole RESET hole CHANNEL number (1-3) Battery compartment (Battery compartment cover not shown) 3 EN EN GETTING STARTED BATTERIES Batteries are supplied with this product: Main unit Remote unit 3 x UM-3 (AA) 1. 5V batteries 2 x UM-4 (AAA) 1. 5V batteries TABLE STAND OR WALL MOUNT Use the stand on the back of the main unit / remote sensor, or mount it on a wall with a nail. To attach the main unit stand: Insert batteries before first use, matching the polarity (+ and -) as shown in the battery compartment. For best results, install batteries in the remote sensor before the main unit. To use the main unit wall mount: NOTE It is recommended that you use alkaline batteries with this product for longer performance. UNIT Main Remote LOCATION Indoor Temperature / Humidity Area Outdoor Temperature / Humidity Area Installing the batteries: To use the remote sensor stand or wall mount: CHANGE SETTINGS To change, time, calendar and language settings: 1. Press and hold MODE for 2 seconds to enter setting mode. (To reach the setting you want quickly, press and hold or . ) 3. Press MODE to confirm. REMOTE SENSOR (THGR122NX) This product is shipped with a THGR122NX Thermo / Hygro Sensor that collects Temperature and Humidity data. Data can be collected from up to 3 sensors. Additional sensors sold separately. SETUP SENSOR 1. Open the remote sensor battery compartment with a small Phillips screwdriver. Insert the batteries, matching the polarity (+ and -) as shown in the battery compartment. SWITCH OPTION Channel Channel 1-3. If you are using more than one sensor, select a different channel for each sensor. 4 3. The switch is located in the battery compartment. Then, press and hold MEM and CHANNEL on the main unit to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor. (Refer to the "Data Transmission" section for more information. ) 5. Close the remote sensor battery compartment. Secure the sensor in the desired location using the wall mount or table stand. SEARCH FOR SENSOR To search for a sensor, press and hold MEM and CHANNEL (on the main unit) for 2 seconds. NOTE If the sensor is still not found, check the batteries, obstructions, and remote unit location. NOTE Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. This is normal and does not affect general product performance. [. . . ] Each sensor's data will be displayed for 3 seconds. NOTE If you use a sensor that collects only temperature data, humidity will not be shown. NOTE For more information on the sensor see "Remote Sensor THGR122NX" Section. SILENCE ALARM When the alarm time is reached, the crescendo alarm will sound for 2 minutes. [. . . ]