User manual OREGON SCIENTIFIC BAR638HG WIRELESS WEATHER STATION

[. . . ] Wireless Weather Station Model: BAR638HG / BAR638HG-2 / BAR638HGU / BAR638HGU-2 USER MANUAL CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Back View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] : Press to activate or deactivate alarm 2 BAR638HG_M_EN_6. p65 2 2005. 4. 27, 10:56 PM LCD DISPLAY REMOTE SENSOR (THGR122NX) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1. 4. Wall mount hole RESET hole CHANNEL number (1-3) Battery compartment (Battery compartment cover not shown) 3 BAR638HG_M_EN_6. p65 3 2005. 4. 27, 10:56 PM EN EN GETTING STARTED BATTERIES Batteries are supplied with this product: Main unit Remote unit 3 x UM-3 (AA) 1. 5V batteries 2 x UM-4 (AAA) 1. 5V batteries TABLE STAND Insert batteries before first use, matching the polarity (+ and -) as shown in the battery compartment. For best results, install batteries in the remote sensor before the main unit. shows when batteries are low. NOTE It is recommended that you use alkaline batteries with this product for longer performance. UNIT Main Remote LOCATION Indoor Temperature / Humidity Area Outdoor Temperature / Humidity Area REMOTE SENSOR (THGR122NX) This product is shipped with a THGR122NX Thermo / Hygro Sensor that collects Temperature and Humidity data. Data can be collected from up to 3 sensors. Additional sensors sold separately. Installing the batteries: SETUP SENSOR 1. Open the remote sensor battery compartment with a small Phillips screwdriver. Insert the batteries, matching the polarity (+ and -) as shown in the battery compartment. CHANGE SETTINGS To change, time, calendar and language settings: 1. Press and hold MODE for 2 seconds to enter setting mode. (To reach the setting you want quickly, press and hold or . ) 3. Press MODE to confirm. SWITCH OPTION Channel Channel 1-3. If you are using more than one sensor, select a different channel for each sensor. 3. The switch is located in the battery compartment. Then, press and hold MEM and CHANNEL on the main unit to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor. (Refer to the "Data Transmission" section for more information. ) 4 BAR638HG_M_EN_6. p65 4 2005. 4. 27, 10:56 PM 5. Close the remote sensor battery compartment. Secure the sensor in the desired location using the wall mount or table stand. NOTE If the sensor is still not found, check the batteries, obstructions, and remote unit location. NOTE Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. This is normal and does not affect general product performance. The reception will resume once the interference ends. CLOCK The clock automatically synchronizes the current time and date when it is brought within range of the radio signal DCF77 generated from Frankfurt, Germany for Central Europe (model BAR638HG / BAR638HG-2) or MSF60 generated from Rugby, England (model BAR638HGU / BAR638HGU-2). [. . . ] NOTE If you use a sensor that collects only temperature data, humidity will not be shown. NOTE For more information on the sensor see "Remote Sensor THGR122NX" section. SET ALARM 1. Press to confirm. ACTIVATE ALARM Press to activate or deactivate the alarm. shows in the Clock / Alarm Area when the alarm is activated. SILENCE ALARM When the alarm time is reached, the crescendo alarm will sound for 2 minutes. [. . . ]