User manual OREGON SCIENTIFIC BHB613AWF

[. . . ] A ' Sunny ' forecast reflects fine clear weather. HOW TO READ THE PRESSURE TREND CHART Stored memory of the barometric pressure changes are displayed on the chart, in 5 steps indicating the pressure 1, 3, 6, 12 and 24 hours ago. This chart is plotted by comparing the past barometric pressure to the present pressure. This gives you the pressure trend over the last 24 hours. The weather will be getting better ( worse ) if this chart shows the bar marks moving up ( down ) towards the present time. [. . . ] Increase/decrease the altitude in steps of 10 meter by pressing [ ] or [ ] button. Press the [ SET ] button again to set the altitude. At this time the previous pressure display will reappear. If the altitude has been changed, the ' ALT ' indicator flashing (about 15 minutes ) until a new sampling takes place and the pressure reading is then compensated with the new altitude. Press the [ SET ] button 6 times to confirm the setting you just entered or wait for one minute for automatic exit. Note: For monitoring the local barometric pressure reading, the user needs to select the 0 meter ( preset value ) for the altitude setting. For monitoring the Sea Level barometric pressure reading at certain altitude, the user needs to select the local altitude (-100 to 2500 meters i. e. -328 to 8223 feet) for the altitude setting. The BHB-613 requires entry of elevation in meters not feet. Therefore, to convert feet to meters, multiply feet by 0. 3048. To determine your location elevation, please either contact your local library, TV/ radio weather forecaster, or via Intenet at www. worldatlas. com/aatals/infopage/ elevation. htm. Important: 1. The accuracy of weather forecasting when using pressure trend alone is about 70 to 75 percent and, therefore, we cannot be held responsible for any inconveniences caused by an inaccurate weather forecast. 2 HOW TO SELECT THE BAR OR LINE CHART FOR THE PRESSURE TREND To get the line chart display, press the [RESET] button at the bottom of the unit while pressing and holding the [SET] key in the bar chart display. To get the bar chart display, press the [RESET] button once. Connector: Use wall-mount connector to align with other wall-mount bracket if necessary. - Note: Either action will reset the unit and the previous readings/ setting will be lost. Wall Mount Connector Wall Mount Bracket CONNECTOR Un-install the brackets: HOW TO SELECT THE PRESSURE UNITS OF MEASURE The switch in the battery compartment of the weather station selects between hPa/mb and inHg. To select hPa/mb, set the switch to hPa/mb. To select inHg, set the switch to inHg. LOW BATTERY SIGNAL INDICATION If the voltage of the batteries becomes low, the " " indicator will be displayed. Replace the batteries when the " " indicator is displayed. TABLE STANDING OR WALL MOUNTING Table Standing : Your unit comes with stand connector for connecting it to the other modular units. MAINTENANCE When handled properly, this unit is engineered to give you years of satisfactory service. Here are a few product care instructions: 1. [. . . ] Read this instruction manual thoroughly before operating the unit. STAND CONNECTOR Wall mount bracket 3 GB GB SPECIFICATION Pressure measuring range : 794 to 1050 hPa/mb ( 24. 45 to 31. 00 inHg) Altitude compensation for barometric pressure reading : -100 to 2500 meters (-328 to 8223 feet) 1 hPa/mb (0. 03inHg) 15 minutes Four pcs. UM-4 or "AAA" size batteries 9 month 6. 64" x 2. 32" x 1. 28" ( H xWxD) 4. 80 ounces (without battery) Pressure display resolution Pressure sampling cycle Power source : : : Battery life Dimension : : Weight : CAUTION -- The content of this manual is subject to change without further notice. -- Due to printing limitation, the displays shown in this manual may differ from the actual display. -- The contents of this manual may not be reproduced without the permission of the manufacturer. CUSTOMER ASSISTANCE Should you require assistance regarding this product and its operation, please contact our customer care department at 800853-8883 or via email at helpme@oscientific. com. WARRANTY This product is warranted to be free of manufacturing defects for a period of 1 year from date of retail purchase. [. . . ]