User manual OREGON SCIENTIFIC RM318PU

[. . . ] Please see the Trouble Shooting section for further information. P l e a s e a l s o d o n 't h e s i t a t e t o c a l l 8 8 0 - 8 5 3 - 8 8 8 3 ( o r e m a i l helpme@ocientific. com)if you have any question about setting up and/or using your new Kids Projection Clock. In the meantime, all of us at Oregon Scientific hope you enjoy this revolutionary advance in time keeping technology. ON / OFF (Figure A. 4) This button turns the alarm function on and off. Touching the ON/OFF button one time will either turn the alarm on or off. [. . . ] Due to possible interference, the best reception often occurs between midnight and 4 a. m. The clock not only sets itself to synchronize its digital time and date with the Atomic clock's signals, but it also automatically adjusts for daylight-savings time!Your clock utilizes a small internal antenna that double as the bedside/desktop stand. (Please see the section on "Signal Strength" for optimal performance of your Kids Projection Clock) The successful reception of the long wave signal depends on the positioning and location of the clock. Insufficient signal strength or external electrical noises may prevent the unit from receiving a complete signal. The main reasons for poor reception are heavily reinforced concrete and steel structures, and close proximity to electrical units such as TV's and PC monitors. RESET MODE / SET (Figure A. 5) Press the MODE key once to switch between the display of either the Day of the Week or Seconds on the clock. Kids Projection Clock will continue to display the selected function (Day or Seconds) until the MODE button id pressed again. IMPORTANT : Holding the MODE key for more than three seconds turns on the manual mode for setting the time, date, year and language (English/French/ Spanish). Please refer to this section for specific setting instructions. (( · )) / 24hOFF (Figure A. 6) Press the (( · )) key once to show the alarm time. The (( · )) /24hOFF icon is displayed in the lower left portion of the screen to alert you that the display is showing the alarm time. To return to the month and date display, press the (( · )) key once. NOTE: The (( · )) Clock will continue to display the selected function (Month /Date or Alarm Time) Until the (( · )) button is pressed again. Setting the Time 1) Press and hold MODE button for at least three seconds. The "Hour" segment of the clock time will begin flashing 2) While the "Hour" segment is flashing press the [ ] button to set the desired hour time (Please note the AM/PM designation) 3) When the desired hour timeis reached press the MODE button again. The "Minutes" segment of the clock time will begin flashing. TROUBLE SHOOTING Problem No Display · · Remedy Check battery compartment. Confirm that batteries are of good quality, and are installed correctly (( · )) Alarm Display indicator (Figure A. 12) This (( · )) icon indicates the second line of the display is showing Alarm Time. 4) While the "Minutes" segment is flashing press the [ desired minutes time. ] button to set the 5) When the desired minutes time is reached, briefly press the MODE button five more times to exit the clock time set mode. · [ ] Alarm " ON " Indicator (Figure A. 13) ] icon indicates that the alarm function is activated. This Bell [ IMPORTANT : As soon as any manual change in the clock time is mode, there is a loss of the signal strength indicator from the display. NOTE : The next sucessful reception of a radio signal will override a manually set clock time showing the clock running manually. Did not receive A time signal If the units are new and just out of the box, allow60- 72 hours cycle for the clock to automatically seek a signal between midnight and 4 a. m. Relocate the clock or the antenna to position near a window. Be certain the antenna cord is fully extended and look for low battery indicator. · [ ] Low Battery Indicator (Figure A. 14) This [ ] icon indicates that it is time to change batteries. Please refer to the Battery Replacement Section of this manual. Setting the Year 1) Press and hold MODE button for at least three seconds. The "Hour" segment of the clock time will begin flashing 2) Briefly press the MODE button and the "Minutes" segment will begin flashing. 3) Briefly press the MODE button once more. The clock time will disappear and be replaced by a flashing year (Ex. [. . . ] Insert the batteries strictly according to the polarities shown therein. NOTE : Please do not become alarmed if the unit does mot receive signal directly from the box. The unit will receive most dependable and interference free signal automatically between Midnight and 4 a. m. If you have any questions please give us a call at 800-853-8883 or reach us by email to helpme@osiientific. com. Setting the Date Press and hold MODE button until the hour segment of the time display flashes Press MODE button four more times until you see the date flash on the display. [. . . ]