User manual OREGON SCIENTIFIC RM816P

[. . . ] 4 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AC Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 About Radio Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Enabling / Disabling Radio Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Insert the batteries strictly according to the polarities shown. Press the [RESET] button. 4 GB GB NOTE Replace the batteries whenever the low battery icon( ) is displayed, the LCD is dim, or the display does not illuminate when the power is on. Replace all the batteries at the same time ­ it is dangerous to mix old and new batteries. Contact your local waste disposal authority for instructions on how to dispose of used batteries. Used batteries can be harmful to the environment, and should not be thrown out with household trash. Connecting to an AC power source Your product comes with an AC power adaptor. Use of the AC power adaptor is required for continuous time projection. Once the power adaptor is in place, you can leave the projector on for a longer period of time (such as throughout the night) by sliding the [PROJECTION ON] switch on the side of the unit. To turn off the projector, slide the switch back. NOTE Note that this switch can only be used with the power adaptor installed. For momentary projection, press the [SNOOZE/LIGHT] button. ABOUT RADIO RECEPTION This product is designed to synchronize its calendar clock automatically once it is brought within range of the radio signal. When the unit is receiving the signal, the Radio Reception symbol with start to blink. Generally, complete reception takes around 2 to 10 minutes, depending on the strength of the signal. The clock automatically searches for radio signal at 1AM, 2AM, 3AM, 9AM, 3PM and 7PM daily. Radio Reception Description Strong reception of radio clock signal. Radio Reception is disabled. 5 NOTE Reception can be affected by a number of factors. For best reception, place the device away from metal objects and electrical appliances. Other causes for signal interference include electrical transmission towers, steel reinforced construction, and metal siding. Reception is ideal when placed near a window. NOTE Even though there are areas that may have more difficulty in receiving a signal, the Atomic Clock contains accurate quartz movement and will retain precise timing even if the signal is missed on a rare occasion. ENABLING / DISABLING RADIO RECEPTION To manually disable the reception of the RF signal, press and hold the [DOWN button for 2 seconds until the Radio Reception symbol completely disappears. ] To enable the reception again, press and hold [UP ] button for 2 seconds. The Radio Reception symbol will blink and the unit will search for the RF signal automatically. TO MANUALLY SET THE CLOCK AND CALENDAR Before you can manually set the clock and calendar, you must specify the current time zone you live in and the time format (12- or 24-hour). Press and hold the [MODE] button for 2 seconds. The time-zone offset hour digits will blink. [. . . ] Take special care when handling a damaged LCD display, as the liquid crystals can be harmful to your health. Do not use or store the device, including the remote sensor, in locations that may adversely affect the product such as rain, snow, desert, and magnetic fields. Do not use this device in aircrafts or hospitals. The use of radio frequency products can cause malfunctions in the control devices of other equipment. [. . . ]