User manual OREGON SCIENTIFIC RMR603HGA

[. . . ] Wireless Thermo-Hygro Clock Model : RMR603HGA User Manual RMR603HGA lab test cover R2 1 1/14/04, 1:31 AM CONTENTS Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About Oregon Scientific . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Humidity Area when the OUTDOOR humidity is shown. CHANGE SETTINGS 1. Press and hold MODE for 2 seconds to enter setting mode. Press MODE to confirm. TABLE STAND OR WALL MOUNT Insert the stand on the back of the product, or mount it on a wall with a nail. Remote REMOTE SENSOR (THGR122NX) This product is shipped with a THGR122NX Thermo/ Hygro Sensor that collects Temperature and Humidity data. Data can be collected from up to 3 sensors. Additional sensors sold separately. 6 RMR603HGA lab test R2 6 1/17/04, 4:52 PM SETUP SENSOR Open the remote sensor battery compartment with a small Phillips screwdriver. Insert the batteries, matching the polarity as shown in the battery compartment. The switch is located in the battery compartment. If you are using more than one sensor, select a different channel for each sensor. For best results: · Insert the batteries and select the channel and temperature unit before you mount the sensor. · Place the sensor out of direct sunlight and moisture. · Do not place the sensor more than 30 meters (98 feet) from the main (indoor) unit. · Position the sensor so that it faces the main (indoor) unit, minimizing obstructions such as doors, walls, and furniture. · Place the sensor in a location with a clear view to the sky, away from metallic or electronic objects. · Position the sensor close to the main unit during cold winter months as below-freezing temperatures may affect battery performance and signal transmission. You may need to experiment with various locations to get the best results. SWITCH Channel 3. Place the sensor near the main unit. Press RESET on the sensor to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor. (Refer to the Sensor Data Transmission section for more information. ) Close the remote sensor battery compartment. Secure the sensor in the desired location using the wall mount or table stand. 4. 5. 7 RMR603HGA lab test R2 7 1/17/04, 4:52 PM EN EN DATA TRANSMISSION Data is sent from the sensor(s) every 40 seconds. The reception icon shown in the Temperature and Humidity Areas shows the status. ICON DESCRIPTION Main unit is searching for sensors. Channel 1 is selected (number will change depending on the sensor you select) The selected sensor cannot be found. [. . . ] Each sensor's data will be displayed for 3 seconds. To end auto-scan, press CHANNEL or MEM. 10 RMR603HGA lab test R2 10 1/17/04, 4:52 PM NOTE If you use a sensor that collects only temperature data, humidity will not be shown. MINIMUM / MAXIMUM RECORDS Press MEM to toggle between current, maximum (MAX) and minimum (MIN) records for the selected sensor. To clear the records, press and hold MEM for 2 seconds. [. . . ]