User manual OREGON SCIENTIFIC RMR939P R8 OP

[. . . ] RF Projection Clock with Remote Motion Sensor Model: RMR939P / MSR939 User Manual RMR939P English Cover R8 OP Black 1 8/23/04, 11:56 AM RF Projection Clock with Remote Motion Sensor Model: RMR939P / MSR939 User Manual Turning the Reception ON / OFF . . . . . . . . . . . . . . . . . . . . . . . . . 13 Clock / Calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Clock / Calendar Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Setting the Clock / Calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It should be unplugged during severe storms or whenever you will be away for a long time. Only use the type of power source specified in this manual. Do not overload power strips and extension cords, as this can cause a fire hazard. CARING FOR THIS PRODUCT To ensure you receive the maximum benefit from using this product, please observe the following guidelines. · Do not clean any part of the product with benzene, thinner or other solvent chemicals - this may cause permanent damage that is not covered by the guarantee. When necessary, clean it with a damp cloth. 10 RMR939P English R8 OP Black 10 · Keep your product away from hot, humid conditions or strong sunlight. · Every effort has been made to ensure the highest standards of reliability for your clock with remote motion sensor. However, if something does go wrong, please do not try to repair it yourself consult your supplier. · Do not use your product outdoors in the rain, or handle it with wet hands - water can damage electrical equipment. GETTING STARTED PACKAGE CONTENTS When you unpack your clock with remote motion sensor, make sure you keep all the packing materials in a safe place, in case you need to later transport the device or return it for servicing. In the box, you will find: · Clock Unit · Remote Motion Sensor · 4 x UM-3 / AA 1. 5V Batteries for the Clock · 6V AC / DC Adaptor for the Clock · 3 x UM-3 / AA 1. 5V Batteries for the Remote Motion Sensor 8/23/04, 11:55 AM BATTERIES The clock uses: · 4 x UM-3 / AA 1. 5V batteries. The motion sensor uses: · 3 x UM-3 / AA 1. 5V batteries. The optional wake-up vibration alarm VR101 (not included in the package) uses: · 2 x UM-3 / AA 1. 5V batteries. NOTE It is recommended that you use alkaline batteries with this product for longer performance. To install the batteries, simply insert them making sure they match the correct polarities (+ and -). For best results, install batteries in the motion sensor before the clock. Press RESET after each battery change. To install the clock batteries: To install the motion sensor batteries: NOTE Do not use rechargeable batteries for the clock or remote motion sensor. 11 RMR939P English R8 OP Black 11 8/23/04, 11:55 AM EN EN shows on the clock display when batteries are low or when there are no batteries installed and only the adaptor is connected. The LED indicator on the motion sensor and vibration alarm will flash in red when the batteries are low. AC ADAPTOR The clock / projector and the motion sensor use 6V and 4. 5V AC / DC adaptors respectively. Press and hold the CLOCK button for 2 seconds. The time zone offset hour digits will flash. +1, the time displayed will be the RF clock time plus 1 hour). You can select 1 of the 5 following languages: SYMBOL LANGUAGE English German French Italian Spanish BACKLIGHT Press SNOOZE / LIGHT to activate the backlight for 5 seconds. TEMPERATURE 2. [. . . ] REMEDY Place the clock far away from PCs, phones, and other electronic equipment and near a windowsill. Turn on the alarm setting. WARNINGS This product is designed to give you years of service if handled properly. Oregon Scientific will not be responsible for any deviations in the usage of the device from those specified in the user instructions or any unapproved alterations or repairs of the product. Observe the following guidelines: · Never immerse the product in water. [. . . ]