User manual OREGON SCIENTIFIC TD339

[. . . ] EN TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The base unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] button. Tip: To return to standby mode, press and hold the Changing the security PIN Your ThermoDECT telephone is shipped with the security PIN (Personal Identification Number) set to "0000". You can change this to any 1-8 digit PIN you choose. The security PIN is used for resetting the system and identifying the telephone in a PABX (Private Automatic Branch Exchange) or local telephone network. Press button. to select Setup from the options. The PIN number will not show on the display for security reasons. Tip: To return to standby mode, press and hold the 15 EN Resetting your telephone system Resetting the system clears all information that you have stored on your telephone ­ such as telephone book entries, caller ID history, and the baby call (emergency call) number ­ and returns your ThermoDECT telephone to its default settings (shown on page 29). There are two ways to reset the system ­ with a security PIN, and without a security PIN. To reset the system with a security PIN: 1. If you enter the wrong PIN number, an Error message displays. A confirmation melody sounds from the handset, and the system resets and flashes the word "Base" on the handset. Hold the handset near the base unit for a few seconds until it finds the base. To reset the system without a security PIN: 1. Slide the battery lid off the back of the base unit. Insert the batteries into the handset, then release the button. The word Default displays on the handset to confirm the system has been reset. Slide the battery lid back onto the unit until it clicks into place. Press to reset the system or to cancel . USING MULTIPLE HANDSETS You can register up to four additional handsets and three additional base units to expand your ThermoDECT telephone system. Additional handsets and base units are sold separately. Handsets are shipped with a charge adapter for recharging their batteries. Note: This ThermoDECT telephone is compatible with most major modern DECT (Digital Enhanced Cordless Telecommunications) telephones. If you already have a DECT system, check to see if the systems are complatible by registering a handset to both base units. Managing multiple handset and base unit registrations A base unit can carry a maximum of 5 handsets on its network. You can make intercom, 3-way, baby monitor, and transfer calls between handsets that are registered to the same base unit, but not to handsets that are registered to a different base unit. Example: The Harris household has seven members: Mum, Dad, Jill, Anna, Sam, Grandma H, and Tom. Because the family has more than five handsets, they own two base units. [. . . ] If you do not wish to hear the beep tone, you can turn it off following the instructions on page 12. Problems with multi-handset use "I'm having problems registering a new handset. " · Sometimes it helps to unplug and then reconnect your base unit to its AC power source before you start the registration procedure. · Make sure you have selected a base number that is not already assigned. Choose a number that does not have a [ ] check mark next to it. · You may have already registered 5 handsets to the base unit. [. . . ]