User manual OREGON TP380

[. . . ] Press and hold MENU to enable monitoring function 1. Select Channel, CTCSS in MENU mode 8 9 Speaker Receives voices / sounds from incoming call BACK VIEW NO. 1 2 3 DESCRIPTION Strap hole Belt Clip Back cover FUNCTION Loop strap through so you can hang unit from your neck Clip to your pocket or belt. Remove to access battery compartment 4 SYMBOL FUNCTION Receiving Transmitting Volume Voice Activation System Key Lock Auto Power Off Key Beeps Roger Beeps Scan Channel or CTCSS Battery Indicator Silent Alert function quietly alerts you of any incoming calls without beeping noises Channel Number: Select between 40 channels (big) CTCSS code: Adjust From 01-38 code (small) 5 EN LCD DISPLAY SYMBOLS EN SAFETY AND CARE INSTRUCTIONS SAFETY PRECAUTIONS Please observe the following safety precautions when setting up and using this product. [. . . ] Before charging, study the user manual section on "Charging Contacts" for further instructions. Reset: At any time if the unit can't work properly, please take off the batteries and insert them again. TALKING INTO TRANSCEIVER 1. Hold down the PTT button and speak into the MIC to transmit ( appears on the LCD). When finished, release the button. 2. The transceiver will automatically play received transmissions. NOTE: You can only communicate with another radio that is using the same channel and/or CTCSS code as your radio. CALL FUNCTION You can send a ringer sound to all transceivers tuned to the same channel and / or the CTCSS code as your transceivers by pressing PTT. Press PTT twice in rapid succession to enable the Call Tone function. Confirm selection in MENU mode. USING THE KEY LOCK You can lock the buttons on the transceiver to avoid accidentally enabling the device. To enable/disable key lock, press PWR + MENU simultaneously. 9 EN EN AUTO-SQUELCH FUNCTION Your transceiver has an Auto-Squelch function for hearing weaker, distant transmissions. You will not hear anything on a channel unless someone is transmitting nearby on the same channel. Press and hold MENU for 2 seconds to enable/disable this function. The transceiver will then toggle between the following configurable settings: SYMBOL SETTING Channel (big) DESCRIPTION Selects channel for transmission Selects a CTCSS code for the current channel Enable/disable voice-activated transmission CTCSS (small) VOX 10 Key Tone Vibrating Automatic Power-Off Enable/disable beep when a key on the transceiver is pressed Enable/disable vibration function Enable/disable automatic shut-off after device is idle for 2 hours NOTE: Press MENU to confirm and move to the next setting. To confirm the changes but quit the Menu Options, press PTT. SELECTING A CHANNEL Select between 40 channels. The transmitter and receiver must be on the same channel. Press MENU once until the channel number starts flashing on the LCD. 2. Press and hold or to begin scanning a channel. If a valid signal is present, the transceiver will pause on the current active channel. Press PTT to stop scanning and exit the menu. Or, press MENU to stop scanning and go to the next Menu Option. CTCSS SCANNING You can activate the channel scan function: 1. Press MENU twice until the CTCSS number starts flashing on the LCD. 11 EN Roger Beep Enable/disable beep heard after the finish of a received transmission 2. [. . . ] Press or key to activate/deactivate the function. NOTE: Press any button to re-enable the transceiver after automatic shut-off. ACCESSORIES CHARGING CONTACTS Your TP380 transceiver comes with 2 individual drop-in chargers that allow you to charge 2 transceivers at the same time using a connector cable and 1 adaptor, You may also charge each transceiver separately by an additional charger that comes with the package. The cradle charger LED lights red during charging, and takes 14 to 16 hours to complete. 15 EN 1. Press MENU 7 consecutive times until appears on the LCD. EN CAUTION: 1. Located inside the transceiver's battery compartment is a charging switch, which must be set to "ON" while charging. If alkaline batteries are used, switch the set to "OFF". [. . . ]