User manual OUTBACK POWER SYSTEMS GFX1424

[. . . ] GFX Series Inverter/Charger GFX1312 GFX1424 GFX1548 Operator's Manual About OutBack Power Technologies OutBack Power Technologies is a leader in advanced energy conversion technology. Our products include true sine wave inverter/chargers, maximum power point tracking charge controllers, system communication components, as well as breaker panels, breakers, accessories, and assembled systems. Contact Information Telephone: +1. 360. 435. 6030 (North America) +1. 360. 618. 4363 (Technical Support) +1. 360. 435. 6019 (Fax) North America 19009 62nd Avenue NE Arlington, WA 98223 USA Support@outbackpower. com www. outbackpower. com +34. 93. 654. 9568 (Barcelona, Spain) Address: E-mail: Web Site: Disclaimer UNLESS SPECIFICALLY AGREED TO IN WRITING, OUTBACK POWER TECHNOLOGIES (a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION. (b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER'S RISK. Warranty Summary OutBack Power Technologies Inc. [. . . ] (See the GFX Series Installation Manual for more stacking instructions. ) Each inverter needs to be assigned a status -- "master" or "slave". The master is the primary and most heavily used unit. Slave inverters provide assistance when the loads are more than the master can handle alone. Programming involves using the system display to assign a status and stacking value to the inverter on each port. See the system display and HUB manuals for programming instructions. HUB4 Additional Ports Port 1 MATE Port MATE Figure 6 IMPORTANT: OutBack HUB4 and MATE The master inverter must always be connected to port 1 on the HUB. Connecting it elsewhere, or connecting a slave to port 1, will result in backfeed or output voltage errors which will shut the system down immediately. Installing multiple inverters without stacking them (or stacking them improperly) will result in similar errors and shutdown. Although stacking allows greater capacity, the loads, wiring, and breakers must still be sized appropriately. Additional terminations and bus bars may be required. Overloading may cause the breakers to trip or the inverters to shut down. CAUTION: Equipment Damage The inverters in a stacked system should all be the same DC voltage, wattage, and model. Do not stack inverters of different wattages. 24 900-0114-01-00 Rev A Operation Classic Series Stacking (Dual-Stack) In "classic" series stacking, two inverters create two separate 120 Vac output phases ("legs"). The other is the slave, which creates a 120 Vac output that is intentionally 180° out of phase with the master. Each of these legs can be used to power a separate set of 120 Vac loads. Collectively they form a "split-phase" configuration. This configuration produces 240 Vac, which can be used to power 240 Vac loads when both inverters work together. This system can continuously power 2. 6 ­ 3. 0 kVA of loads, depending on the inverter model. A single (phase) inverter can power 1. 3 ­ 1. 5 kVA of loads, depending on the inverter model. The two legs operate independently of each other. The 120 Vac loads on each leg cannot exceed a given inverter's wattage. Only two inverters, one per phase, may be installed in a classic series arrangement. 1. 3 kVA 120 Vac 1. 3 kVA 120 Vac 2. 6 kVA 240 Vac 1. 3 kVA 120 Vac 1. 3 kVA 120 Vac Figure 7 Example of Classic Series Stacking Arrangement (Two Inverters) Parallel Stacking (Dual-Stack and Larger) In parallel stacking, two or more inverters are stacked to create a single, common 120 Vac output. The master provides the primary output. The slaves are connected to the same output and assist the master. The slave inverters can be programmed to activate on demand, reducing idle-power consumption. They will remain off until the loads exceed a certain threshold. [. . . ] Product model and serial number; Proof-of-purchase in the form of a copy of the original Product purchase invoice or receipt confirming the Product model number and serial number; Description of the problem; and Shipping address for the repaired or replacement equipment. Upon receiving this information, the OutBack representative can issue an RMA number. 56 900-0114-01-00 Rev A Warranty Returning Product to OutBack After receiving the RMA number, the customer must pack the Product(s) authorized for return, along with a copy of the original purchase invoice and warranty certificate, in the original Product shipping container(s) or packaging providing equivalent or reasonable protection. The RMA number must be written on the outside of the packaging where it is clearly visible. The Product(s) must be shipped back to OutBack Power Technologies in their original or equivalent packaging, to the following address: OutBack Power Technologies RMA # ____________________ 6115 192nd Street NE Arlington, WA 98223 USA The customer must insure the shipment, or accept the risk of loss or damage during shipment. If a shipping box is needed for return of a Product, OutBack will, upon request, send a shipping box. [. . . ]