User manual OUTBACK POWER SYSTEMS SRC-BC4 SCHEMA

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual OUTBACK POWER SYSTEMS SRC-BC4. We hope that this OUTBACK POWER SYSTEMS SRC-BC4 user guide will be useful to you.

Lastmanuals help download the user guide OUTBACK POWER SYSTEMS SRC-BC4.

Mode d'emploi OUTBACK POWER SYSTEMS SRC-BC4

Download

Manual abstract: user guide OUTBACK POWER SYSTEMS SRC-BC4SCHEMA

Detailed instructions for use are in the User's Guide.

 [. . . ] Battery Enclosure Cabling Kit ­ SRC-BC4
For a 48-volt Battery Bank

CAUTION: Equipment Damage
See the SmartRE Installation Manual for detailed information on installing the battery cables,  including torque requirements. Use a DC voltmeter to ensure correct voltage and polarity.  [. . . ] Consult your local electric authority to ensure compliance. Factory wiring is not shown. 

IMPORTANT: Grounding
Battery Negative (­) to Chassis Ground Bond is done through the GFDI. 
#6 AWG THHN recommended

Existing Battery Enclosure
(Batteries shown as wired with SRE-BC1)

1 additional Ground Conductor will be needed

8

Proper cabinet grounding may still be required. Ground conductors are not provided with this kit. Consult local electric code to ensure compliance. This is intended for a Negative Ground installation. Do not use in a Positive Ground installation. 
Main Office 19009 62nd Avenue NE Arlington,  WA USA 1. 360. 435. 6030

900-0106-01-00 Rev A © March 2010 OutBack Power Systems. All Rights Reserved. 

Battery Enclosure Cabling Kit ­ SRC-BC4

Electronics Enclosure

WARNING: Lethal Voltage
Review the system configuration to identify all possible sources of energy. Ensure ALL sources of power are disconnected before performing any installation or maintenance on this equipment. Confirm that the terminals are de-energized using a validated voltmeter (rated for a minimum 1000 Vac and 1000 Vdc) to verify the deenergized condition. Do not perform any servicing other than that specified in the installation instructions unless qualified to do so or as instructed to do so by OutBack Power Systems Technical Support personnel. 

Electronics Enclosure

(Factory wiring not shown) BAT (­) 5a BAT (+)

To prepare the existing installation for the addition of the 2nd Battery Enclosure:
1. Do NOT remove 6 . 
4a

(Factory wiring not shown) BAT (­) 5a

6

2. Remove

5b

and

4b

. 

BAT (+)

6

7a

WARNING: Shock Hazard
Ensure the Inverter Charger Breaker is in OFF position BEFORE making connections. 

3.  [. . . ] Then connect

. 
4 4 7 7 6

Existing Battery Enclosure
(Batteries shown as wired with SRE-BC1)

Existing Battery Enclosure
(Batteries shown rewired to Series/Parallel using SRE-BC4)

6

900-0106-01-00 Rev A © March 2010 OutBack Power Systems. All Rights Reserved. 

Main Office 19009 62nd Avenue NE Arlington,  WA USA 1. 360. 435. 6030 [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE OUTBACK POWER SYSTEMS SRC-BC4

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual OUTBACK POWER SYSTEMS SRC-BC4 will begin.