User manual OUTLAW 1070

[. . . ] Model 1070 7. 1 Channel Surround Sound Receiver Owner's Manual Version 0. 9 Owner's Manual Warnings Please Read First Outdoor Antenna Grounding­If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Lightning­For added protection for the unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power-line surges. [. . . ] You will not see any all-digital formats if you've selected an analog input. Select the one that matches the connections you have made to the input being adjusted. NOTE: Even if you choose a digital input, you will not be able to see all the surround format choices available UNLESS that input is receiving a digital audio signal from your source. Model 1070 7. 1 Channel Surround Sound Receiver 7 Owner's Manual System Setup Setting the Level Trim: To configure the Level Trim of a video input: 1. MovethecursortoLEVELTRIMbyusingthe and buttonson thefrontpanelorremote. Pressthe and buttonsonthefrontpanelorremotetoscroll throughthepreferredleveltrimforthisinput. To configure the Lip Sync Delay of a video input: 1. MovethecursortoLIPSYNCDELAYbyusingthe and buttons onthefrontpanelorremote. Press toincreasetheamountoflipsyncdelay, or todecreaseit. Up to 200ms of delay can be selected in 10ms increments. Choosing Another Input To select another input from the Input Configuration sub-menu: 1. MovethecursortoRETURNTOINPUTMENUbyusingthe and buttonsonthefrontpanelorremote. PressSETonthefrontpanelortheremote. The input choices appear as follows as you scroll through them: 0db-6db-12db These choices allow you to adjust relative audio levels so that when you switch from one source to another, you won't be subjected to a wide disparity in volume. We suggest that you accept the "0dB" default for each input and make changes only after you determine that an input needs "trimming. " Setting Auto Polling To configure the Auto Polling of a video input: 1. MovethecursortoAUTOPOLLbyusingthe and buttonson thefrontpanelorremote. Pressthe and buttonsonthefrontpanelorremotetotoggle betweenONandOFF. The Input Configuration sub-menu appears. . Movethecursortothenewinputthatyouwanttoconfigureby usingthe and buttonsonthefrontpanelorremote. PressSETonthefrontpanelortheremote. You'll see the same configuration sub-menu as you did for the DVD input. You'll configure the remaining video inputs (Video 1-4) by following the same procedures. Remember that the DVI 2 connector is available only when you've selected the Video 2 input. Configuring Audio Inputs In general, the procedures for configuring Audio inputs (Tuner, CD, Tape, and Aux) are very similar to those for configuring Video inputs. Two major differences are: When ON is selected the Auto Poll circuitry will automatically switch the audio input from the selected digital source to the analog input for the source when the digital data stream is interrupted. This is helpful for use with digital cable boxes where the audio switches between digital and analog, depending on which channel is selected. When OFF is selected the Model 1070 will keep the digital input active even when the digital data is interrupted. This is the preferred setting for the DVD input where the digital audio stops during menu setup or when a disc is paused. Setting Bass and Treble You can't choose a video input for any of the four audio sources (the menu line is there but the only choice is "None") There is no Lip Sync Delay available for audio-only sources You'll make both these tone control adjustments in the same way. To configure the Bass or Treble of a video input: 1. MovethecursortoBASS(orTREBLE)byusingthe and buttons onthefrontpanelorremote. Pressthe and buttonsonthefrontpanelorremotetoscroll throughthepreferredtonecontrolsettingsforthisinput. Proceed with configuring the tuner and remaining audio components connected to your Model 1070. Once you have completed the input configuration process for all inputs, your next step is to configure the Model 1070 to match the number and type of speakers in your system. To return to the Main Menu: 1. [. . . ] DTS, DTS-ES, DTS 96/24 and DTS Neo:6 are registered trademarks of DTS, Inc. Any trademark not acknowledged is recognized as the property of the respective owner. Digital Audio All digital audio inputs and outputs are to S/PDIF electrical (75, 0. 5Vp-p), S/PDIF optical (Toslink), or AES / EBU (110, 5Vp-p) standards as appropriate. Processor CS49400 Model 1070 7. 1 Channel Surround Sound Receiver 51 Outlaw Audio Limited Warranty This warranty protects the owner of the Outlaw Model 1070 Surround Sound Receiver (the PRODUCT) for two (2) years from the date of purchase. This warranty covers all defects in material and workmanship with the following specific exceptions. [. . . ]