User manual PALSONIC MODEL 5159

[. . . ] OWNER'S MANUAL 51CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 5159 Type Tested Electrical Safety AS/NZS 3250 Lic 4164 Standards Australia APP No: N15956 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888 Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference. Contents Notes for operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation and Appearance Antenna connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] * If some channel position is tuned by MANUAL TUNING mode, AFC (automatic frequency control) function is defeated in this channel position. 3. 3 SKIP BUTTON 3. 3. 1 FUNCTION When CHANNEL SELECTOR ( )button is used to select channel, the channels will be skipped if they are set to "SKIP" mode. For example: Set 2~7 channels to "SKIP" mode, the procedure of channel position increasing or decreasing is as shown. CHANNEL INCREASE CH 1 8 9 99 0 CH CH CHANNEL DECREASE (REMOTE) 1 8 9 99 0 (THE APPLIANCE) 3. 3. 2 OPERATION: 3. 3. 2. 1 Press PRESET ON/OFF button to set preset mode. 3. 2. 2 Select a channel by using CHANNEL SELECTOR button. 3. 3. 2. 3 Press "SKIP" button, "SKIP" will be-displayed on the screen to indicate that the channel is at "SKIP" mode. SKIP llllllllllllll 3. 4 Repeat 2~3 steps to skip another channel. 5 Press PRESET ON/OFF button to exit preset mode. 3 SKIP 3. 4 CHANNEL SELECTION 3. 4. 1 This set is preset to Australia channels 2, 7, 9, 10, 28 on those numbers. If you wish to change the settings, or add more channels the method is quite straight forward. 3. 4. 2 Press CHANNEL SELECTOR ( )on the appliance, the channel number will be increased or decreased as shown in the following Fig. , and displayed in the upper right corner of the screen. 4 CHANNEL INCREASE CH 1 2 3 99 0 CH CH 8 CHANNEL DECREASE (REMOTE) 1 2 3 99 0 (THE APPLIANCE) 3. 5 VOLUME CONTROL 3. 5. 1. Press the VOL button to increase volume ; the green bar on the screen moves right. button to decrease volume ; the green bar on the screen moves left. Display of maximum volume Display of minimum volume . . . . . . . . . . . . . . . . . . . . . . . . . 3. 6 AV/TV SELECTOR Press AV/TV button to change TV mode to AV mode when the set is in receiving (TV) mode. On the contrary, press it to change AV mode to TV mode when the set is in VIDEO mode. 3. 7 TINT CONTROL Use this knob to control colour tone during reception of pictures when using the NTSC system. 5 4. REMOTE CONTROL OPERATION: REMOTE CONTROL UNIT : STANDBY 1 ~ 9 : DIGITAL CHANNEL SELECTOR 10/0 : CHANNEL 10 OR CHANNEL 0 SELECTOR SYSTEM : COLOUR SYSTEM CONTROL -/- : DIGIT OR TWO DIGIT CHANNEL SELECT : PREVIOUS : CHANNEL SELECTOR : VOLUME CONTROL : PERSONAL PREFERENCE SELECT (BRIGHTNESS, COLOUR) : PICTURE/TIME ADJUSTMENT PICTURE : PICTURE CONTROL DSP : DISPLAY CH VOL PPS 4. 1 INSTALLING BATTERIES: 4. 1. 1 Remove the battery cover of Remote Control Unit. 4. 1. 2 Insert two "AAA", 1. 5V batteries, making sure the polarity ( + or - ) of the batteries matches the polarity marks inside the unit. 4. 1. 3 Close the battery cover NOTE: * When the Remote Control Unit is not used for a long time or the batteries are worn out, take out the batteries to prevent electrolyte leakage. * Take care not to drop, dampen, dissemble the Remote Control Unit. 4. 2 STANDBY BUTTON Refer to 3. 1. 6 4. 3 CHANNEL SELECTION 4. 3. 1 Press CHANNEL SELECTOR ( ) the channel number will be increased or decreased and displayed in the upper right corner of the screen. 4. 3. 2 Use the DIGITAL CHANNEL SELECTOR button for direct channel selection. 1) 1~10 channel Method 1: Example: To select channel 2 Press -/-- - Press 2 2 (Display) Press -/-To select channel 10 -- Press 10/0 10 Method 2: Example: To select channel 2 Press -/--- Press 10/0 10 Press 2 2 To select channel 10 Press -/--- Press 1 1- Press 10/0 10 2) 11~99 channel To select channel 28 Press -/--- Press 2 2- Press 8 28 3) 0 channel Press -/--- Press 10/0 0- Press 8 0 7 4. 3. 3 PREVIOUS BUTTON Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous previous programme you watched was was on channel 15; then you can press the button to reach channel 15, press it again to return channel 6. 6 4. 4 SOUND CONTROL 5 4. 4. 1 VOLUME CONTROL 4. 4. 1. 1 Press the VOL button to increase volume; the green bar on the screen moves right. 4. 4. 1. 2 Press the VOL button to decrease volume; the green bar on the screen moves left. [. . . ] VIDEO PLAYBACK 5. 1. 1 The figure below shows how to connect the TV set to the video equipment. 5. 1. 2 Press the AV/TV button on the TV set or on the remote controller to select VIDEO mode, "VIDEO" will be displayed on the screen. The picture shown on the screen is the program from the video equipment. NOTE: The VCR signal can be input by antenna input socket of the TV set, but the quality of the picture and sound is not better than that of video mode. 5. 2. RECORDING FROM THE TV SET 5. 2. 1 The figure below shows how to connect the TV set to the VCR. 5. [. . . ]