User manual PALSONIC MODEL 5160G

[. . . ] OWNER'S MANUAL 51CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 5160G Type Tested Electrical Safety AS/NZS 3250 Lic 4164 Standards Australia APP No: N15959 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888 Contents Contents Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain this manual in an easily accessible location for future reference. Note: Screen displays and illustrations in this manual may differ from the actual ones for better visibility. CONTENTS 1 2 4 4 5 6 7 7 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The aerial cable should not be bundled with the power cord and the like. 8 Connect to video and audio equipment This TV set provides 2 groups of AV input terminals for your convenient connection to VTR, DVD or video camera to enjoy the high quality picture. Please refer to the owner's manual of the equipment to be connected as well. Important notes on the AV input terminals Please do not connect and use the front and rear input terminals at the same time. You can also use the AV terminals on the TV set rear as follows. ! Notes: Please do not connect and use the S-VIDEO and VIDEO terminals at the same time. Please note that the rear audio input terminals are stereo while the front are mono. 9 Operations Turning on/off Turning on/off Turning on 1 2 3 ! Press the Power Switch on the TV set. If no picture appears, then the TV set is in STANDBY mode. Now please follow step 2. In STANDBY mode, press the button on the remote controller and the TV set is turned on. In STANDBY mode, you can also press the AV/TV button on the set to turn on. Notes: If there is no input signal, then a blueback appears. After 15 minutes, the set auto goes to STANDBY. Turning off the Power Switch on the 1 Press off the power completely. TV set if you want to cut 2 If you want to turn off the TV set temporarily, press the button on the remote controller. 10 Operations Select Input Signal Select input signal Select input signal 1 Press AV/TV button on the TV set or AV button on the remote control. When the set is in TV mode, press this button and the set goes to AV mode. Now you could watch video program from AV input terminals. If you want to switch to TV press AV button again or follow step 2, 3 or 4. 2 Press digit buttons to switch back to TV mode. 3 Press CH+ or CH- button to switch back to TV mode. 4 Press 5 button to switch back to TV mode. Press DSP button, the set displays current input mode. The OSD disappears in about 5 seconds. 18:09 19 !Notes: If the Timer item has been set, the current time also appears. 11 Operations 1 2 3 Press MENU button four times to call Program menu page. Press CH+ or CH- buttons to select item. Press VOL+ or VOL- buttons to adjust item. Tuning in Auto search/Manual search/Channel skip/Fine tuning Auto Search 1 2 3 ! Press MENU button repeatedly to enter into Program menu page. Press CH+ or CH- button repeatedly to select Auto Search item. Press VOL+ button to start Auto Search towards higher frequency; or press VOL- button to start Auto Search towards lower frequency. All active channels will be preset and stored into the memory automatically. After presetting, the TV will stop at the last channel program. Notes: 1. Before you start Auto Search, we strongly recommend you to set a proper Sound System according to your local area. Please refer to the steps of Sound System setting on page 14. During the process of AUTO SEARCH, pressing the MENU or CH+/- buttons will stop the process. Manual Search Use MANUAL SEARCH function if desired channels cannot be preset or if you would like to preset channels to specific position numbers one by one. 1 2 3 4 5 ! Notes: Press MENU button repeatedly to enter into Program menu page. Press CH+ or CH- button repeatedly to select Channel Number item. Press VOL+ or VOL- button to select a channel number (ranging from 0-254). [. . . ] Press Picture mode | button and picture mode icon displays. Before the icon disappear, continue to press 4, 3, 2, 1 on the remote control. Control C. Press VOL+ or VOL- button to switch between Off and On. Hotel Lock Child Lock off off 20 Child Lock/Game Child Lock Firstly, please refer to the Hotel mode on the previous page to enter into the Control menu page. Press CH - button to select Child Lock item and then press VOL+ or VOL- button to switch between On or Off. [. . . ]