User manual PALSONIC MODEL 5169M

[. . . ] Preset menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Function menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Channel selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Picture and volume adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When "SKIP ON" is set, the current channel program will be skipped. Making use of this function can skip some unwanted channel, say 5, 11, next when you press CH button to select channel, 5, 11 channel will be skipped. 0 1 4 6 10 12 * Press the channel direct select button can select the skipped channel. 3) AFT ON/OFF Making use of the AFT function can automatically fine tune the channel. Select and highlight AFT, pressing VOL button it toggles between ON and OFF. When in AFT ON, it can automatically fine tune the channel. In normal circumstances, please set AFT ON. When in the process of manual search, AFT is set "OFF" automatically. 4) Band Selection Press the CH button to highlight BAND. Press the VOL change sequence is VL VH U button to select band. The 5) SYS (sound system) This item is used to select sound system. Since this TV model's RF sound system is B/G only, this item gets into ineffectiveness in sound system selection. 6) Auto - search (AUTO) Press CH button to highlight AUTO. Press VOL button the set will automatically search and store the active TV signals in your local area from lower band to 9 higher band in the sequence of VL VH U with the green bar moving rightward. When a station is located, the set will store the signals with a channel number from 0. When all the signals are searched and stored, the TV returns to 0 channel automatically, auto-search is finished. * After auto-search, all programs colour system is set to AUTO and in AFT-ON mode. * During the process of auto-search, if MENU or CH button is pressed, the searching is interrupted. Press VOL button the searching begins again. 7) SEARCH Making use of SEARCH function will store a TV program at a referred channel position. Select a channel number, when SEARCH is highlighted, press VOL button, the set begins to search for signals upward or downward from current channel. When a station is located, the searching stops and the program is stored into the referred channel position. Repeat the above step and store another program signals into another position. If two channels are same, the previous will be deleted. When the searching is finished, to store the program signals you should press the MENU button to exit the menu and the program signals are stored automatically. * When the tuning changing reaches the highest (lowest), the searching turns to next band's lowest (highest) and continues searching. If the signals are not the signals you desire, you can press the VOL button again until the desired signals are searched. 8) Manual search (MANUAL) When some program's picture or sound is not good, you can make use of this function to fine tune the tuning voltage. [. . . ] Should the problem be unsettled, unplug the set and contact your dealer. Symptoms Check these things Try these adjustment . . No picture, no sound. Poor sound, picture OK. Poor picture, sound OK. Snowy picture Lines in picture Distorted picture Weak picture. May be local interference from appliance. [. . . ]